FE-FC Holden Discussion Forum
November 27, 2024, 02:58:40 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: The FE-FC Holden Car Club of NSW are proud to host the 19th FE-FC Holden Nationals. Check out the announcement video for more.
 
   Home   Help Search Calendar Login Register  
FE-FC Holden Discussion Forum > Technical Board > Modification Help (Moderators: RET, Glenn 'Stinky' Stankevicius, gp) > Commodore Accel Pedal Pics
Pages: [1]   Go Down
« previous next »
  Add bookmark  |  Print  
Author Topic: Commodore Accel Pedal Pics  (Read 5070 times)
Glenn 'Stinky' Stankevicius
Moderator
Guru
*****
Offline Offline

Model: FE and FC
Posts: 5135


Willaston, South Australia


Glenn.Stankevicius
View Profile
« on: August 11, 2012, 02:15:16 PM »
0
I have a Commodore Accelerator pedal but in the rush to complete the car (for the Philip Island Nats all those years ago Roll Eyes ) I fitted in the easiest location, but obviously not the best for the operation of the pedal.
I'd appreciate some feedback and pictures on the best location that provides comfortable operation and full travel.
Logged
http://forum.fefcholden.club/index.php/topic,18001.0.html
JB
qld-club
Guru
*****
Offline Offline

Model: FE
Posts: 1914



Jason Blanchard
View Profile
« Reply #1 on: August 11, 2012, 02:41:46 PM »
0


I just basically put it where the booster hole was cut for simplicity... Different floor though than the original.

Cheers
JB
Logged
Phone +64 223509263
Glenn 'Stinky' Stankevicius
Moderator
Guru
*****
Offline Offline

Model: FE and FC
Posts: 5135


Willaston, South Australia


Glenn.Stankevicius
View Profile
« Reply #2 on: August 11, 2012, 02:56:00 PM »
0
Thanks JB, from memory the difficulty was where the cable came through the firewall, as I have a booster on the firewall my choices were limited.

Anyone else?
Logged
http://forum.fefcholden.club/index.php/topic,18001.0.html
NES304
Guru
*****
Offline Offline

Model: FC
Posts: 2874


Yes Dear


nes304
View Profile
« Reply #3 on: August 11, 2012, 03:48:18 PM »
0
I went with the VT setup as it fit fairly straight forward (JB loves this combo too)
http://fefcholden.org.au/forum/index.php/topic,21578.40.html
I have a complete set from a VS and never tried to fit it but will check in the next few days.
Logged



marc.nesbitt13@yahoo.com.au
mcl1959
vic-club
Guru
*****
Offline Offline

Posts: 6155


FE's rule


View Profile
« Reply #4 on: August 11, 2012, 07:55:30 PM »
0
Sorry I don't have a pic but there is a flat piece of firewall just south of and to the left of my booster (looking from the engine bay). It seemed to be just perfect for both the pedal position and cable entry past the booster. Booster was a UC item.

Ken
Logged
FCV08
Senior Member
****
Offline Offline

Model: FC
Posts: 692


FE FC Club of QLD


View Profile
« Reply #5 on: August 11, 2012, 11:58:04 PM »
0
Stinky

I will take some extra photos as I have fitted the cable between the VN V8 booster and the inner guard.

I have modded the mount and adjusted the angles for the pedal to get the required travel.

The pedal mounts quite near where the original handbrake mounts through the firewall.

Will try and post tomorrow night.

Regards

Craig D
Logged
FCV08
Senior Member
****
Offline Offline

Model: FC
Posts: 692


FE FC Club of QLD


View Profile
« Reply #6 on: August 14, 2012, 11:30:55 PM »
0
Stinky

Please find some photos on the location of the accelerator cable access through the firewall. Please note it is a VN  V8 Booster.

I have removed the section from the donor car and drilled a hole to suit diameter then spot welded from inside and seal with sikaflex from inside.







Hope this helps

Cheers

Craig
Logged
Glenn 'Stinky' Stankevicius
Moderator
Guru
*****
Offline Offline

Model: FE and FC
Posts: 5135


Willaston, South Australia


Glenn.Stankevicius
View Profile
« Reply #7 on: August 15, 2012, 10:21:59 AM »
0
Thanks
Logged
http://forum.fefcholden.club/index.php/topic,18001.0.html
NES304
Guru
*****
Offline Offline

Model: FC
Posts: 2874


Yes Dear


nes304
View Profile
« Reply #8 on: August 17, 2012, 12:22:50 PM »
0
I am about to rip out my VT setup as I have to clean out the engine bay. Did you want me to hold in the VS version to show you?
Logged



marc.nesbitt13@yahoo.com.au
Glenn 'Stinky' Stankevicius
Moderator
Guru
*****
Offline Offline

Model: FE and FC
Posts: 5135


Willaston, South Australia


Glenn.Stankevicius
View Profile
« Reply #9 on: August 17, 2012, 05:22:23 PM »
0
That'd be great thanks.
Logged
http://forum.fefcholden.club/index.php/topic,18001.0.html
NES304
Guru
*****
Offline Offline

Model: FC
Posts: 2874


Yes Dear


nes304
View Profile
« Reply #10 on: August 17, 2012, 10:22:55 PM »
0
Roger, Called into work 5am tomorrow so I'll get onto prob tomorrow night.
Logged



marc.nesbitt13@yahoo.com.au
NES304
Guru
*****
Offline Offline

Model: FC
Posts: 2874


Yes Dear


nes304
View Profile
« Reply #11 on: August 21, 2012, 08:03:59 PM »
0
I think these look like VS pedals?
http://fefcholden.org.au/forum/index.php/topic,21248.20/topicseen.html
Logged



marc.nesbitt13@yahoo.com.au
Pages: [1]   Go Up
  Add bookmark  |  Print  
« previous next »

Share this topic...
In a forum (BBCode) 
In a site/blog (HTML)

 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.041 seconds with 21 queries.