FE-FC Holden Discussion Forum
November 01, 2024, 10:55:32 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: The FE-FC Holden Car Club of NSW are proud to host the 19th FE-FC Holden Nationals. Check out the announcement video for more.
 
   Home   Help Search Calendar Login Register  
Pages: [1]   Go Down
  Add bookmark  |  Print  
Author Topic: seat surrounds  (Read 9240 times)
Jonno
Senior Member
****
Offline Offline

Posts: 332



View Profile
« on: October 13, 2005, 06:18:26 AM »
0

Here are some photos of FE vs EK seat surround mounts, in response to this thread in 'Parts Wanted' (I thought it more appropriate now in this section):
http://www.fefcholden.org.au/cgi-bin/yabb/YaBB.cgi?board=pwntd;action=display;num=1128921577

I should start by saying that I 'think' my FE seat is an FE seat. I was a little confused by the fact it has a rear ashtray mount and I have a ute....but folks seem to think this in just a mass produced item. Anyway, as far as I can tell, the only difference between the two is that the EK seat is about 4cm lower in height and has slightly different mounts for the seat surrounds.

The front mounts are identical:



The rear corner mount is slightly different:



and the mounting point on the rear vertical is in a slightly different place:



All you would need to do to fit a metal EK surround to an FE/FC seat would be to grind off the tab 'A', fabricate a tab 'B', and then add an extra plate on the vertical to screw into. Here is the EK surround fitted:



hope this helps.

Jonno
« Last Edit: October 13, 2005, 06:25:31 AM by Jonno » Logged

Cottles Bridge, VIC
craiga
Guest
« Reply #1 on: October 13, 2005, 07:17:35 AM »
0

Great post Jonno.  VERY helpful, and much appreciated for the quality and content.

Cheers,

Craig.
Logged
Jonno
Senior Member
****
Offline Offline

Posts: 332



View Profile
« Reply #2 on: October 13, 2005, 07:55:00 AM »
0

thanks Craig,

I should probably add that I haven't actually DONE this mod myself as I'm thinking about using the entire EK seat set-up. But I have looked at both fairly closely...and can't see any reason why it wouldn't work fine.

Jonno
Logged

Cottles Bridge, VIC
20.4_seconds
Senior Member
****
Offline Offline

Posts: 342


The ox is slow, but the earth is patient!


View Profile
« Reply #3 on: October 13, 2005, 08:48:31 AM »
0

Cheers Jonno,
Clear and detailed and great pics too...I knew about the front part and was hoping to find out about the rear without too much investigation...thanks so much Jonno...great work dude...

Nick
Logged

All I  want for Christmas is a Smiths clock bracket and knurled knobs
Sarge
Guru
*****
Offline Offline

Posts: 1218


My 57 & Old No 7 all a Man Need's


View Profile
« Reply #4 on: October 15, 2005, 08:30:30 AM »
0

Jonno
       Thanks for the heads, up as I am fitting EK metal surround to the FC seat. Now I know to do the tab before it goes to the trimmers.

Cheers
Sarge
Logged

Mark Lees Tallerbudgera Queensland
        0421 165 351
Holden Classics; a BREED above the rest
Roybeth
Full Member
***
Offline Offline

Model: FC
Posts: 249



View Profile
« Reply #5 on: November 20, 2020, 07:45:27 AM »
0

Jonno
        Thanks for the heads, up as I am fitting EK metal surround to the FC seat. Now I know to do the tab before it goes to the trimmers.

Cheers
Sarge

Hi Guys - think this may be the thread I was looking for? but of the course the pics are not available anymore  Sad
Logged
Roybeth
Full Member
***
Offline Offline

Model: FC
Posts: 249



View Profile
« Reply #6 on: November 22, 2020, 09:17:10 AM »
0

Here's the project, from the tabs on my seat seems the metal surrounds are not as wide along the seat edge where the tabs are. Some have suggested removing or shortening these tabs and screwing into the frame at the back top edge.

126372441_209375907237615_8179032132094247124_n by Helen Sheedy, on Flickr

Logged
Roybeth
Full Member
***
Offline Offline

Model: FC
Posts: 249



View Profile
« Reply #7 on: November 22, 2020, 09:18:13 AM »
0

Heres the front tab of the seat

125883051_1519765788214529_9133323997448378977_n by Helen Sheedy, on Flickr

Logged
Roybeth
Full Member
***
Offline Offline

Model: FC
Posts: 249



View Profile
« Reply #8 on: November 22, 2020, 09:21:42 AM »
0

and the back, which I imagine will be the one I will modify - have to more precisely check out the fit of the front tab to the metal surround in case both will need to be done.

125545419_284802776267638_128672697081424616_n by Helen Sheedy, on Flickr
Logged
Pages: [1]   Go Up
  Add bookmark  |  Print  

Share this topic...
In a forum (BBCode) 
In a site/blog (HTML)

 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.032 seconds with 20 queries.