FE-FC Holden Discussion Forum
November 23, 2024, 12:13:40 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Are you a member of one of the FE-FC Holden Car Clubs of Australia ? If you are, get access to the Club-Member-only area of this discussion board. Send an IM to the board admin, including your real name and club to get access.
 
   Home   Help Search Calendar Login Register  
FE-FC Holden Discussion Forum > For Sale and Wanted > Parts Wanted (Moderators: RET, Glenn 'Stinky' Stankevicius) > Rear divider mould
Pages: [1]   Go Down
« previous next »
  Add bookmark  |  Print  
Author Topic: Rear divider mould  (Read 3552 times)
DJ
Guru
*****
Offline Offline

Model: FC
Posts: 1405



View Profile
« on: November 29, 2013, 11:01:51 AM »
0
Still after a pair (or even one) of these elusive suckers. If anyone has come across any recently that they wish to sell I would love to hear from you.
Dave.
Logged
Dave
0417 270 315
hsv-001
Senior Member
****
Offline Offline

Posts: 909


View Profile
« Reply #1 on: November 29, 2013, 08:11:37 PM »
0
I'm sure I have 1 somewhere but I used fe door card moulds on my van . I am in the process of putting a flash on the sides of my VW project and noticed that the later beetle side chrome strip [the thin one] is much the same profile and can be slid on over 6# self tapping screws will get you photos tomorrow . Cheers Haydn.
Logged
DJ
Guru
*****
Offline Offline

Model: FC
Posts: 1405



View Profile
« Reply #2 on: November 29, 2013, 08:35:59 PM »
0
Thanks Haydn.
Logged
Dave
0417 270 315
FCRB26
Guru
*****
Offline Offline

Model: FE and FC
Posts: 3802


peter.mallaby
View Profile
« Reply #3 on: November 29, 2013, 09:20:29 PM »
0
Ill check my stash tommorow for you..


Pete
Logged
http://www.mallaby.com.au
DJ
Guru
*****
Offline Offline

Model: FC
Posts: 1405



View Profile
« Reply #4 on: November 29, 2013, 11:26:44 PM »
0
Thanks Pete
Logged
Dave
0417 270 315
hsv-001
Senior Member
****
Offline Offline

Posts: 909


View Profile
« Reply #5 on: November 30, 2013, 10:25:56 AM »
0
As I was saying last night , I have one original ,it seems to have a mark where the bumper has been pushed against it. On my van are FE chrome strips off the door cards [shown in photo]


they are easier to fit anyway .Also have 2 chrome  offcut  strips off late VW beetle which is the same profile that can be fitted directly over 6# self tapping screws or a piece of doorcard chrome strip . Which ever suits you. Cheers .Haydn
Logged
DJ
Guru
*****
Offline Offline

Model: FC
Posts: 1405



View Profile
« Reply #6 on: November 30, 2013, 12:59:36 PM »
0
Haydn,
Thanks a lot. Will be back home tonight & reply. Leaning towards the 2 chrome off cut strips.
Dave.
Logged
Dave
0417 270 315
fcwrangler
nsw-club
Guru
*****
Offline Offline

Model: FC
Posts: 1258


JIM-- Gilead NSW


Jim Tuckwell
View Profile
« Reply #7 on: November 30, 2013, 04:40:12 PM »
0
Dave, if you are still after a pair of the dividers,I did a clean up and found a set.
Jim
Logged
on the seventh day: God Made Holden
DJ
Guru
*****
Offline Offline

Model: FC
Posts: 1405



View Profile
« Reply #8 on: November 30, 2013, 08:15:00 PM »
0
Jim,
Thanks, please fwd details for payment. A photo would be great if possible.
Dave.
Logged
Dave
0417 270 315
DJ
Guru
*****
Offline Offline

Model: FC
Posts: 1405



View Profile
« Reply #9 on: November 30, 2013, 08:17:15 PM »
0
Haydn,
Many thanks for your help. I may have been exceptionally luck withe a couple on offer from Jim. I'll try of this original pair.
Dave.
Logged
Dave
0417 270 315
DJ
Guru
*****
Offline Offline

Model: FC
Posts: 1405



View Profile
« Reply #10 on: November 30, 2013, 08:18:14 PM »
0
Quote from: FCRB26 on November 29, 2013, 09:20:29 PM
Ill check my stash tommorow for you..


Pete

Pete, I could be OK after all. Thanks.
Dave.
Logged
Dave
0417 270 315
Pages: [1]   Go Up
  Add bookmark  |  Print  
« previous next »

Share this topic...
In a forum (BBCode) 
In a site/blog (HTML)

 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.029 seconds with 19 queries.