FC parts clean out

[2door350]

Hi all,

Had to move a heap of parts i had stashed under a friends house, for the first time in years i have got a reasonable idea of what parts i have.  If anyone needs anything specific PM me and have a look through the boxes of stuff as i sort them out....i hate selling stuff but i'm on a roll at the moment so get into it before i stack it all away and forget about it again...hahaha

Some of the bigger things i've found so far

Bonnet - FC special, dent and rust free, a really good one $150
13 x 7 Alloy 5 slots - CSA Brand, would polish up a treat, no gutter rash, fitted with servicable 215/50/13 TA's (may separate tyres) $500
14x8(2) and 14x7(2) Dragway Splats with new looking 235/60/14 and 225/60/14 tyres $600
bumperettes? painted yellow (hahaha) but dent free suit repaint or re-chrome $200 pair
Found heaps of starter motors and a few alternators (no generators yet...) for some reason - any offers?
original front windscreen - $50
Redline 4 barrel manifold suit red 6 - looks as new- $150
390 holley 4160 - was a reco when i purchased it years ago - used for 12 months or so, been sitting for maybe 5 years so could do with a gasket set atleast.... $250
Open spacer above to suit 4bbl $10
rusty but straight fc hub caps x 4 $80
chrome dress rims - various condition - will have to check sizes
FC radiator - look to be in good nick $50
202 bottom end - was line bored, bored and honed when rebuilt, acl duralite's and acl bearings, JP straight cuts, was a virgin block before rebuild (thinks it's +20 now, will have to look) no cam -done maybe 20 000 k's max, again - been sitting for a few years now wrapped up...$600
Toyota 5 speed box, was noisy at idle so removed and replaced with another i had at the time, suit re-bearing or put up with the noise  for $100
Used Red 6 oil cooler setup includes lines, sandwich plate and cooler, good looking setup $80
Sun visors x 4 offers
single stromberg on red six manifold, was on a ht ute i had years ago, ran well but been sitting...$30
Muncie to Chev bellhousing (suit the large style flywheel?) $100
Muncie case - i used for dummy fit ups - no internals or side cover $120
FC Chromed firewall carb linkage $80
HR disc Spindles/rotors/calipers $260
LH disc spindles (cant find calipers and rotors yet but may have them) $80

WILL ADD MORE AS I DIG THROUGH SECOND LOAD....

Happy to send pictures to serious buyers and post at buyers expense (i'm in Hobart), i've got a lot on at the moment so bare with me i don't get back to your messages straight away

Cheers

2Door350

[spybo]

Id be interested in the bonnet...where in Oz are you?

[Royal]

  Hi  Would you have 2 thumbprint dress rims, like EJ premier, in amongst you bits.?
                                 Roy

[2door350]

no, all dress rims are plain

[2door350]

Happy to send pictures to serious buyers and post at buyers expense (i'm in Hobart), i've got a lot on at the moment so bare with me i don't get back to your messages straight away

[2door350]

CSA 5 Slots SOLD

[ptr540]

hi would you have a fc grill and blinkers ?

[Ol_Girl_58]

PM sent re: oil cooler. 

[Ken's 57]

PM sent re starter motor.

[Franno]

I'm chasing a couple of rear interior grab handles (dark green). Maybe a long shot, but had to ask!

[Ken's 57]

Franno - when I bought my FE it had two red grab handles even though the rest of the trim was Summit Blue. As the handles were in good nick I decided to have them spray-painted using a special vinyl paint and the appearance and finish is identical to the original look. That was about 3 years ago and there have been no problems. If you have a good pair that aren't green it may be worth considering.

Ken

[GMB-58FC]

Message sent.

[2door350]

5 speed SOLD(pending payment)
firewall linkage SOLD
oil cooler setup SOLD
radiator SOLD
Starters SOLD
CSA 5 slots SOLD