FE-FC Holden Discussion Forum
November 16, 2024, 01:44:11 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: The FE-FC Holden Car Club of NSW are proud to host the 19th FE-FC Holden Nationals. Check out the announcement video for more.
 
   Home   Help Search Calendar Login Register  
Pages: [1]   Go Down
  Add bookmark  |  Print  
Author Topic: Getting paint off door rubbers  (Read 2615 times)
fe2ek
vic-club
Full Member
***
Offline Offline

Posts: 233


I love YaBB 1G - SP1!


View Profile
« on: October 19, 2004, 06:49:13 AM »
0

Is there an easy way to get paint overspray off door rubbers.It was painted quite a few years back by the previous owner and I want to tidy things up a bit,but i dont want to pull the rubbers out as some are still ok.

Cheers Geoff
Logged
Glenn 'Stinky' Stankevicius
Moderator
Guru
*****
Offline Offline

Model: FE and FC
Posts: 5135


Willaston, South Australia


Glenn.Stankevicius
View Profile
« Reply #1 on: October 19, 2004, 10:05:06 AM »
0

I'd test these ideas on an old throw-away piece before doing it to the car.

1. Chemical - thinners or paint stripper on a rag, may eat the rubber though, watch the surrounding paintwork too.

2. Abrasive - steel wool, scourer or fine sanding block

3. Chemical - I picked up some degreaser the other day, biodegradable, made from sodium hydroxide and other salts. Stripped the grease off the parts a treat and softened the paint on the brush I was using. I think this is the same gear a company called Minus Paint use to strip cars of paint etc, a side-effect of the process is that is reguvenates rubber.
Logged

FCwagon
vic-club
Senior Member
****
Offline Offline

Model: FC
Posts: 462



View Profile
« Reply #2 on: October 19, 2004, 08:12:23 PM »
0

If it's only light overspray, to prevent damage to rubber & duco I've had success using some cutting polish. Cleaned up the excess dried polish with an old toothbrush. Hope this works for you too.
Leigh
Logged

Red & white is alright
craiga
Guest
« Reply #3 on: October 19, 2004, 08:33:37 PM »
0

Try Prepsol (Wax and Grease Remover). If its acrylic the paint will come straight of as it softens, if its enamel the you'll need to work a bit harder, maybe with a light scourer pad.

Good Luck.

Craig.
Logged
fccool59
Senior Member
****
Offline Offline

Posts: 954


rain sucks     http://www.yout ube.com/watch?v =N1Uj


View Profile WWW
« Reply #4 on: November 11, 2004, 11:37:38 AM »
0

Iv'e never had a problem using thinners to remove acrylic overspray of rubbers, they used thinners a lot for cleaning rubber pedals etc in the 60's and 70's.
another way is to gently scrape it with a razor.
becuase the rubber is flexible it usually comes of just by scraping it with your finger nail.
polishes and compounds will take a long time and you will have to rub the shit out of the rubber with a solvent like prepsol or white spirit as the polish will leave a white residue ingrained in the rubber.
Alkaline type water base degreasers will leave streaky oxidization on the paint, they will only be effective as a lubricant while you scrub the rubber, white spirit would be more effective and safer as a lubricant that stays wet longer than prepsol but it will dry the rubber a little bit, vaseline can be rubbed in to rejuvinate the rubber, this is often coloured and sold as a silicone free rubber rejuvinator, you could probably use it as a lubricant to scrape the rubber with as well.
make sure you rub of all the excess vaso as it holds dust and gets messy.
Logged

rain sucks  http://www.youtube.com/watch?v=N1Ujma1lBac    rain sucks     rain sucks
Pages: [1]   Go Up
  Add bookmark  |  Print  

Share this topic...
In a forum (BBCode) 
In a site/blog (HTML)

 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.034 seconds with 22 queries.