FE-FC Holden Discussion Forum
March 29, 2024, 06:10:24 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: The FE-FC Holden Car Club of NSW are proud to host the 19th FE-FC Holden Nationals. Check out the announcement video for more.
 
   Home   Help Search Calendar Login Register  
Pages: [1]   Go Down
  Add bookmark  |  Print  
Author Topic: Ute rear window screen seal problem  (Read 7096 times)
FC-V8
Senior Member
****
Offline Offline

Model: FC
Posts: 424


Not enough hours in the day


View Profile
« on: December 29, 2019, 10:16:40 PM »
0

Hi guy. Ive had the ute on the road for the last few months but I've been having a problem with the rear screen nearly falling out. Its like the glass isnt big enough allowing the seal to much room to move. Has anyone else had this issue and if so who did you overcome it?
Its a rarespares seal.
Cheers
Glenn
Logged

What it to rev ? install a CHEV !
0401-065-201
Harv
Guru
*****
Offline Offline

Model: other Holden
Posts: 1318


View Profile
« Reply #1 on: December 30, 2019, 07:06:51 AM »
0

I’ve got a Rares rear screen rubber in my daughter’s EK ute. The holes for the two divider strips were waaaay off (and had to be redrilled) but other than that the fit is great.

Are you sure it is FE/FC glass? There was some discussion not too long ago (either here or the FB/EK forum) on how the later glass appears similar but is not.

Cheers,
Harv
Logged
mcl1959
vic-club
Guru
*****
Offline Offline

Posts: 6155


FE's rule


View Profile
« Reply #2 on: December 30, 2019, 07:32:12 AM »
0

Yes, I agree with Harv, I seem to remember a discussion that went along the theme that people thought the centre section of the Ute glass was all the same between FE and EK. Apparently because of body sag issues in FE and FC utes, the glass in FB and EK is smaller. Not only the side pieces, but the centre section as well.
The side pieces are easily distinguished as being different, but the centre section is only slightly smaller on FB EK.

Ken
Logged
fcwrangler
nsw-club
Guru
*****
Offline Offline

Model: FC
Posts: 1257


JIM-- Gilead NSW


Jim Tuckwell
View Profile
« Reply #3 on: December 30, 2019, 10:55:09 AM »
0

From past experience, the FE/FC ute rears are different to the FB/EK rears. Rare Spares list different parts for both utes, so this would also suggest there is. From memory, the FE/FC are larger even though they are the same shape. So my question for Glenn is, are the glasses you have from the vehicle, or did you buy them? If the latter, then it could be possible that they are FB/EK, hence the reason they are falling out.
Logged

on the seventh day: God Made Holden
FireKraka
Senior Member
****
Offline Offline

Model: FC
Posts: 646


View Profile
« Reply #4 on: December 30, 2019, 11:08:10 AM »
0

I'm with the rest of you guys, when I was gathering parts for Frankenstein (my EK Ute) I wound up with a couple of sets of back window glass and quickly noted that the sets were different so just had to figure out which was right for the EK and put the other one (FE/FC I assume) away.
Neil
Logged
fcwrangler
nsw-club
Guru
*****
Offline Offline

Model: FC
Posts: 1257


JIM-- Gilead NSW


Jim Tuckwell
View Profile
« Reply #5 on: December 30, 2019, 11:29:37 AM »
0

I should have mentioned that I have fitted both original glasses to both utes and apart from the divider bar holes being wrong. Both FE/FC and FB/EK were a good tight fit and sealed up well to the body.
Logged

on the seventh day: God Made Holden
FC-V8
Senior Member
****
Offline Offline

Model: FC
Posts: 424


Not enough hours in the day


View Profile
« Reply #6 on: December 30, 2019, 04:21:14 PM »
0

Hi guys
The glass was fitted before resto so it should be fc glass. Im have to every now and again push the glass and rubber back from the outside in and relip the rubber over the top body lip.
Glenn
Logged

What it to rev ? install a CHEV !
0401-065-201
mcl1959
vic-club
Guru
*****
Offline Offline

Posts: 6155


FE's rule


View Profile
« Reply #7 on: December 30, 2019, 04:52:48 PM »
0

I’m not really familiar with utes but don’t the two retainer bars stop the windows from going out as you describe?

Ken
Logged
fcwrangler
nsw-club
Guru
*****
Offline Offline

Model: FC
Posts: 1257


JIM-- Gilead NSW


Jim Tuckwell
View Profile
« Reply #8 on: December 30, 2019, 05:48:20 PM »
0

Hi Glenn, I’m trying to get my head around the problem, with this in mind there are a few questions.
1— did you have a new rubber fitted?
2— if so was it a tight or loose fit?
3—was the old rubber sealed or glued in?
finally— is it possible to measure the glass at the joiner on both the corners and centre glass?
Logged

on the seventh day: God Made Holden
FC-V8
Senior Member
****
Offline Offline

Model: FC
Posts: 424


Not enough hours in the day


View Profile
« Reply #9 on: December 30, 2019, 06:07:37 PM »
0

The seal is new and professionally fitted, the fitter actually said it was the easiest one he has fitted so i guess its loose. I will try to upload some photos to show the issue.
Glenn
Logged

What it to rev ? install a CHEV !
0401-065-201
Errol62
Guru
*****
Offline Offline

Posts: 1149


View Profile
« Reply #10 on: December 30, 2019, 07:38:14 PM »
0

Have you been back yo the fitter Glenn?

Sent from my SM-A705YN using Tapatalk
Logged
FC-V8
Senior Member
****
Offline Offline

Model: FC
Posts: 424


Not enough hours in the day


View Profile
« Reply #11 on: December 30, 2019, 08:38:12 PM »
0

Yeah i did. He said no it should be loose then put his hand inside against the window and pushed, the whole window popped out, then goes yeah your right (no shit). His solution was to put sealastic on it which has not improved it at all if snything its worst because now sealastic goes everywhere when i try to get it back in place.
Logged

What it to rev ? install a CHEV !
0401-065-201
fcwrangler
nsw-club
Guru
*****
Offline Offline

Model: FC
Posts: 1257


JIM-- Gilead NSW


Jim Tuckwell
View Profile
« Reply #12 on: December 30, 2019, 09:26:24 PM »
0

This to me shows the glass is to small, even though they were in the ute, doesn’t mean they are correct. I have fitted a few of these over the last few years and also a few FB/EK’s, one of which was Harv’s daughters ute. As stated before, each ute used the Rares rubber, and the only problem was the upright rubber having the holes in the wrong place. The middle holes are correct but depending on were the bar was placed, you had to drill out either the top or bottom hole to allow the bar to fit correctly. I’ve only ever had to seal the glass and body with normal mastic sealer.
Logged

on the seventh day: God Made Holden
FC-V8
Senior Member
****
Offline Offline

Model: FC
Posts: 424


Not enough hours in the day


View Profile
« Reply #13 on: December 31, 2019, 06:04:57 AM »
0

I sure the guy fitting it had to redrill the two bottom holes for the dividers
Glenn
Logged

What it to rev ? install a CHEV !
0401-065-201
ipg
Junior Member
**
Offline Offline

Posts: 90


I love YaBB 1G - SP1!


View Profile
« Reply #14 on: December 31, 2019, 07:20:14 AM »
0

you have fb-ek glass.
when you put the fe-fc glass in it will fit perfectly.
you can reuse your rubber, but you have the wrong glass.
the glass you have is not fe-fc it is fb-ek.
you need to buy fe-fc glass.
Logged
Stewy
sa-club
Senior Member
****
Offline Offline

Model: FE
Posts: 881


FErgus 1957 FE Special Station Sedan


Jeff Stewart
View Profile
« Reply #15 on: December 31, 2019, 01:17:01 PM »
0

Just a thought, can you check on the glass for the date code on the "ARMOURPLATE" logo?
My 1957 FE has the dot over the P for 1957, my FC has the dot over the L for 1958.
I assume that the FB/EK would be different.

Cheers Stewy   Cool
Logged

No matter how much you push the envelope, It'll still be stationery
FC-V8
Senior Member
****
Offline Offline

Model: FC
Posts: 424


Not enough hours in the day


View Profile
« Reply #16 on: December 31, 2019, 03:22:19 PM »
0

Great idea. Ive checked the main rear window and it has a very faint dot(if it is) over the T.
Checked main rear section and its 330mm high just near the divider strip.
Glenn
« Last Edit: December 31, 2019, 03:31:55 PM by FC-V8 » Logged

What it to rev ? install a CHEV !
0401-065-201
fcwrangler
nsw-club
Guru
*****
Offline Offline

Model: FC
Posts: 1257


JIM-- Gilead NSW


Jim Tuckwell
View Profile
« Reply #17 on: December 31, 2019, 04:53:24 PM »
0

The dot over the T would make the year 0, so this would suggest the theory that they are FB/EK  glasses. I’ve asked for measurements from FE/FC glass so we can compare the two.
Logged

on the seventh day: God Made Holden
Pages: [1]   Go Up
  Add bookmark  |  Print  

Share this topic...
In a forum (BBCode) 
In a site/blog (HTML)

 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.032 seconds with 20 queries.