FE-FC Holden Discussion Forum
March 30, 2024, 12:26:41 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Are you a member of one of the FE-FC Holden Car Clubs of Australia ? If you are, get access to the Club-Member-only area of this discussion board. Send an IM to the board admin, including your real name and club to get access.
 
   Home   Help Search Calendar Login Register  
Pages: [1]   Go Down
  Add bookmark  |  Print  
Author Topic: pearlcraft steering wheel  (Read 10862 times)
GMHwagoon
Senior Member
****
Offline Offline

Model: FC
Posts: 384



View Profile
« on: June 29, 2015, 05:02:35 PM »
0


 Anyone had a fc steering wheel done at pearl craft lately
 was wondering the price of getting mine done in the pearl look
 my wheel has only a couple of cracks so needs repair anyway.
 so though l might get it done


   THANKS GREG
Logged
Stewy
sa-club
Senior Member
****
Offline Offline

Model: FE
Posts: 881


FErgus 1957 FE Special Station Sedan


Jeff Stewart
View Profile
« Reply #1 on: June 29, 2015, 06:04:46 PM »
0

Just had a look on the pearlcraft facebook site and there was a question from last month.
A single colour wheel in ok condition was $600 and a two tone was $800.

Cheers Stewy   Cool
Logged

No matter how much you push the envelope, It'll still be stationery
GMHwagoon
Senior Member
****
Offline Offline

Model: FC
Posts: 384



View Profile
« Reply #2 on: June 29, 2015, 06:10:58 PM »
0



   thanks stewy

    l had one done for a ek holden  from the bloke at cockatoo 
   was  really happy with the finish and quality    and it  it was no where
    near that price , so may have to go  standard and just get it repaired and painted black again

  thanks greg
Logged
Brad
Senior Member
****
Offline Offline

Posts: 308


My FC Van in 1986 and I still have It


View Profile
« Reply #3 on: July 08, 2015, 10:07:28 PM »
0

Hello Greg
              I did a wheel on my FB a couple of years ago . I cleaned / opened out the cracks with a hacksaw blade then filled in the gaps with araldite. Sanded and filed it back then got a mate to paint it in two pak black. looked as good as new and Cost less than $100.
       Brad.
Logged

Id rather have a full bottle in front of me than a full frontal labotomy
Harv
Guru
*****
Offline Offline

Model: other Holden
Posts: 1318


View Profile
« Reply #4 on: July 09, 2015, 06:40:18 AM »
0

There are a few threads around on how to repair the cracks yourself with epoxy, or the Ukneadit type stuff found at SuperCheap. A quick sand and ready for paint. Relatively quick job, and will cost you under $15 to do yourself.

Scotty's thread here shows how to deliver your own pearl effect (the trick is in his magic finger templates):
http://www.fbekholden.com/forum/viewtopic.php?f=5&t=8344&hilit=steering+wheel
Scotty uses an airbrush, but you could do the same with rattle-cans and some patience. Some clear coats (more clear = more depth), and you can probably have the paint done for $20 worth of rattle cans.

All up probably a $35 job, and you get the exact colour you want.

Cheers,
Harv
Logged
GMHwagoon
Senior Member
****
Offline Offline

Model: FC
Posts: 384



View Profile
« Reply #5 on: July 09, 2015, 04:01:46 PM »
0



    l had painted one a while back
     problem was because the wheel has a bit of flex in it
     specially around the hub where the arms join  you tend to get
     small hair line cracks mostly in  the paint
      because the paint had little give in it
       there was a product you could add to the paint to give it a bit of give is this still available
        or what type of paint is best for steering wheels

       thanks greg
     
Logged
Harv
Guru
*****
Offline Offline

Model: other Holden
Posts: 1318


View Profile
« Reply #6 on: July 09, 2015, 06:33:26 PM »
0

Not sure about paint anti-hardener, but I do know that a common trick on the repair side is to pin the cracks. The epoxies are great fillers, they just don't stick to plastic too well. You need someway of pinning the two different materials together.

Before using the epoxy or Ukneadit, chase out the steering wheel cracks a bit with a die grinder or Dremel, all the way down to the steel frame of the steering wheel. Open them out to about 10-15mm wide. Don't be scared, the steel frame will hold the wheel together. 

Once the cracks are opened out, drill holes diagonally into the cuts, for the filler to key into. The diagonal direction of the holes help to pin the plastic to the filler, preventing the two moving apart. Horizontal holes, or using no holes at all, allows the filler/plastic interface to move apart, leading to pain cracks.

With the cracks ground and the pinning holes drilled, knead up the Ukneadit and force it into the cracks, pushing it into the pinning holes as you go. Leave the surface proud for sanding.

Sand, prime and paint.

Cheers,
Harv
Logged
hsv-001
Senior Member
****
Offline Offline

Posts: 909


View Profile
« Reply #7 on: July 10, 2015, 08:44:25 PM »
0

I can explain how to do this if its good enough .



Any size you want and any colour. Cheers Haydn
Logged
Harv
Guru
*****
Offline Offline

Model: other Holden
Posts: 1318


View Profile
« Reply #8 on: July 11, 2015, 06:32:23 AM »
0

I can explain how to do this if its good enough .

Yes please Haydn. I'm interested to hear how you get that effect - the more detail the better.

I'm no airbrush Picaso, but when the alternative is $800, I'm willing to give it a try.

Cheers,
Harv
Logged
Errol62
Guru
*****
Offline Offline

Posts: 1149


View Profile
« Reply #9 on: June 08, 2020, 01:28:15 PM »
0

Haydn,
That reminds me of how we used to paint our bikes when we were kids. White enamel then use a candle flame to create black smoke effect.


Sent from my iPad using Tapatalk
Logged
Pages: [1]   Go Up
  Add bookmark  |  Print  

Share this topic...
In a forum (BBCode) 
In a site/blog (HTML)

 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.031 seconds with 20 queries.