New Laws er: Raising and lower vehicles.. VSI 50

[Martin]

Out of curiosity, I read the new regulation that affects you guys in NSW.  There are a few things that some of you have misinterpreted, and I suggest you go and read it again properly.

For instance, it is not retrospective.  The final clause reads:

This VSI applies to vehicles modified or presented to an AUVIS after 31 July 2009.

and

How do you measure the height?  There are even diagrams to explain this - and none of the instructions or diagrams refer to measuring the headlight height.

and

It has to be passed by parliament:  No it doesn't - it's a standard that is issued by the RTA under existing Road Transport Regulations.  It doesn't need any further approvals.

Read it again fellas.

Martin

[Ed]

It's a draconian law brought in to give police greater powers to defect every car in sight at the local "hoon" hot spots.

I doubt very much the police would defect an Old Holden for the sake of it.

Although having said that, it will be more difficult to rego a new build, but being the resourceful bunch we are I'm sure we will get around it.

The police cannot possibly know when a car was presented to an AUVIS, so the simple solution is to get it passed, then do the suspension mods.

In my opinion, this law encourages builders to modify suspension after inspection, and in some cases this will compromise safety.

I'm planning on bagging a future project, will now need to incorporate adjustable bump stops, some remote valves and a discreet install.

as the current law is written, even my rodeo with wound down torsion bars would fail, and its far from low.

Cheers

Ed

[CraigA]

Its retrospective simply because a car that was legally registered six months ago now can't be registered without meeting the new requirements - and for some guys - like me with a 25mm lowered 2007 model car, it means that I can be requested to submit to an AVUS inspection and told to raise the car or submit an engineers certificate. If you add the lower profile tyres then I maybe outside the 50mm maximum and in all sorts of sh*t.

All for a car that it slightly lowered using quality aftermarket springs by a qualified mechanic.

Here's a picture of my illegal car, taken just before it became out-of-control posed a risk to other road users.  >:(



What concerns me is that my car could be uninsured because it does not meet these RTA requirements, UNLESS I go and get an engineers report at my cost to prove its 'safe'.

The new law is a reactionary and poorly constructed by-product of the complete dickheads who late model drive cars around on the bump stops and ruin it for everyone else. Thanks  ::)

[Ed]

hmm.... stupid.

maybe they will get rid of the law like they did with the stupid Motorcycle exhaust labelling law they tried a few years back.

[NO NAME]

from what ive heard they might be dropping the 4wd laws but sticking with the lowering laws since the 4wd groups have been so active against it.

[FC427]

  ;D LOOKS LIKE THE PRESSURE IS OFF FOR THE MOMENT ON IMPLEMENTING THESE NEW LAWS AND WE SLAY LOW FOR NOW  ;D........FC427........                                                                                                                                                                                                   NSW MINISTER FOR ROADS
MICHAEL DALEY MP
NEWS RELEASE
MINISTER AGREES TO FURTHER CONSULTATION ON
CAR MODIFICATION LAWS
Wednesday 29 July 2009

Minister for Roads Michael Daley today met with representatives from the 4WD community and car industry who asked for the introduction of proposed vehicle modification rules to be delayed and for more time to consult.
Mr Daley said he agreed to put the rule changes on hold and that more consultation was needed following the meeting.
“I’ve listened to feedback from the industry and the community, and have agreed to set up a working party to look more closely at how we are going to address this road safety issue,” he said.

“All of those who attended today’s meeting agreed that safety is paramount and that unsafe modifications of vehicles do need be stamped out.
“The working group will include representatives from the NSW Centre for Road Safety, Four Wheel Drive NSW-ACT, Australian Automotive Aftermarket Association, the Australian 4WD Industry Council as well as other agencies and experts,” Mr Daley said.

Executive Director of Australian Automotive Aftermarket Association Stuart Charity said this was a terrific outcome.
“We’re passionate about road safety and we understand the intent of the regulation is to make the roads safer,” he said.
We’re looking forward to working towards a practical solution that meets road safety objectives while also taking industry views into account,” Mr Charity said.

Greg Redfern from Four Wheel Drive NSW-ACT also welcomed the outcome and said the working group would have their full support.
“We want to eliminate unsafe practices in the driving community and we’ll work with the government to make sure these new regulations meet those objectives without any adverse consequences for the motoring community at large,” he said.

“We all agree that there is no place for extreme and illegal modifications, but the clubs in our association follow a strict code of conduct and ethics, and we want to make sure they’re not punished,” Mr Redfern said.
_________________

[FB_MAD]

 ::)

Good to see that common sense has had a win...... for today at least  :-\ :-\ :-\

[customFC]

Interesting blog regarding this issue, written by engineering signatory.
http://you-have-to-be-kidding.blogspot.com/2009/07/car-hoons-news-release.html
Regards
Alex

[customFC]

If you read the above blog, you would have seen that these regulations have been put on hold.
Help make sure they stay that way by signing up to the petition being compiled by the Oposition Minister, Andrew Stoner MP here:
http://www.nothoons.com.au/
Regards
Alex