FE-FC Holden Discussion Forum
September 30, 2024, 04:11:20 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: The FE-FC Holden Car Club of NSW are proud to host the 19th FE-FC Holden Nationals. Check out the announcement video for more.
 
   Home   Help Search Calendar Login Register  
Pages: [1]   Go Down
  Add bookmark  |  Print  
Author Topic: creaking clutch pedal  (Read 3794 times)
fc_ute
Full Member
***
Offline Offline

Posts: 207


I love YaBB 1 Gold!


View Profile
« on: March 16, 2004, 01:44:07 PM »
0

every time i depress the clutch pedal in the ute it makes a creaking noise which actually seams to come from the return spring. i have lubed all pivot points but it still makes this load creaking noise. any suggestions to quiet it down?
craig
Logged
oldgmh
Junior Member
**
Offline Offline

Posts: 92


I love YaBB 1G - SP1!


View Profile
« Reply #1 on: March 16, 2004, 08:50:03 PM »
0

I had a creak which came from the pedal pivot bush on top of the pedal.  It was difficult to get to and lubricate but persistance with a can of WD40 fixed it.
Logged
fastjbav6
wa-club
Senior Member
****
Offline Offline

Posts: 494


OK start her up !


View Profile
« Reply #2 on: March 17, 2004, 07:23:01 AM »
0

G'Day Gary,
You will find that the creaking noise is the large return spring.
Lube both ends of the spring. It's usually the end connected to the pedal.
Use black moly grease or Never Sieze.

Seb
Logged

Yellow Knight
             
Effie C
Senior Member
****
Offline Offline

Model: other Holden
Posts: 822


Still Lost & Confused


View Profile WWW
« Reply #3 on: March 17, 2004, 07:45:08 AM »
0

Another more likely source of the creak is the sintered bronze bush which is installed in the top of the pedal assemble, if you ignore this it will wear the cross shaft and then you have to find one of those.
About Time Spares have thses bush's NOS and reasonable priced, I recently replaced both of mine and it makes a huge difference to the pedal movement, they have to be prelubricated before installation as per the workshop manual.

http://www.abouttimespares.com.au/

They are not too bad to replace the hardest part was getting the individual pedals out, I have a heater demister installed in the way,if it was not there it would be a piece of the proverbal (About 2 hours from start to finish with the heater in the way). Oh I do have a bench press which made it easier to push in and out.

Good Luck
John M

PS WD40 is a very short term fix as it actually wash's the grease out of the bush.
« Last Edit: March 17, 2004, 07:46:23 AM by fcmayberry » Logged

LIVE LIFE ONE DAY AT A TIME,FOR TOMORROW MAY NEVER COME!

Photo Site:http://img53.photobucket.com/albums/v161/EffieC/
ChrisB
Senior Member
****
Offline Offline

Posts: 259


"Shiny Bits"


View Profile
« Reply #4 on: March 17, 2004, 09:47:10 AM »
0

Johno, you forgot to add the time to find and fix the pinched wire   Grin


ChrisB   Cool
Logged
Effie C
Senior Member
****
Offline Offline

Model: other Holden
Posts: 822


Still Lost & Confused


View Profile WWW
« Reply #5 on: March 17, 2004, 10:27:29 AM »
0

True but that was a Qld problem, a bit like starter motors and oil pressure and of course gearbox's Roll Eyes
Logged

LIVE LIFE ONE DAY AT A TIME,FOR TOMORROW MAY NEVER COME!

Photo Site:http://img53.photobucket.com/albums/v161/EffieC/
fc_ute
Full Member
***
Offline Offline

Posts: 207


I love YaBB 1 Gold!


View Profile
« Reply #6 on: March 17, 2004, 12:42:19 PM »
0

thanks guys, i think i will just have to stick my head under there again and lube everything that moves
craig
Logged
Vinnie
Junior Member
**
Offline Offline

Posts: 55


I love YaBB 1G - SP1!


View Profile
« Reply #7 on: March 17, 2004, 02:12:21 PM »
0

Just a note Wd 40 is not a long term lubricant, it is like a degreaser, penetrant etc. and you will find the noise will return- try lithium grease as it comes in a can and easy to use.
Logged
Pages: [1]   Go Up
  Add bookmark  |  Print  

Share this topic...
In a forum (BBCode) 
In a site/blog (HTML)

 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.036 seconds with 19 queries.