FE-FC Holden Discussion Forum
December 04, 2024, 04:28:37 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Are you a member of one of the FE-FC Holden Car Clubs of Australia ? If you are, get access to the Club-Member-only area of this discussion board. Send an IM to the board admin, including your real name and club to get access.
 
   Home   Help Search Calendar Login Register  
Pages: [1] 2   Go Down
  Add bookmark  |  Print  
Author Topic: FC Ute refresh  (Read 8252 times)
Wasim
Full Member
***
Offline Offline

Model: FC
Posts: 145


View Profile
« on: February 21, 2023, 03:46:47 PM »
+2

Here are some pictures of my Ute I’m in the process of refreshing.

Cheers, Wasim









Sent from my iPhone using Tapatalk
Logged

South Australia
my8thholden
nsw-club
Senior Member
****
Offline Offline

Model: FC
Posts: 837



View Profile
« Reply #1 on: February 22, 2023, 09:37:10 AM »
0

nice work , those pressed floor panels are really good , better than patch on patch on patch ...
Logged

these days i'm half as good for twice as long
FireKraka
Senior Member
****
Offline Offline

Model: FC
Posts: 649


View Profile
« Reply #2 on: February 22, 2023, 12:58:10 PM »
0

Nice work Wasim, looking good
Logged
Wasim
Full Member
***
Offline Offline

Model: FC
Posts: 145


View Profile
« Reply #3 on: February 26, 2023, 12:59:33 PM »
0

I bought an old rear window demister about 20 years ago and I guess it was already 20 years old back then?

Anyway it fitted up OK - I was concerned it may have lost it’s “stickiness”.
 



 


Sent from my iPhone using Tapatalk
Logged

South Australia
Stewy
sa-club
Senior Member
****
Offline Offline

Model: FE
Posts: 881


FErgus 1957 FE Special Station Sedan


Jeff Stewart
View Profile
« Reply #4 on: February 26, 2023, 10:42:32 PM »
0

Looking great Wasim, keep up the great work.

Cheers Stewy   Cool
Logged

No matter how much you push the envelope, It'll still be stationery
my8thholden
nsw-club
Senior Member
****
Offline Offline

Model: FC
Posts: 837



View Profile
« Reply #5 on: February 28, 2023, 06:57:31 AM »
0

rear widow de fogger , what you going to drive in movies Huh?
Logged

these days i'm half as good for twice as long
Errol62
Guru
*****
Offline Offline

Posts: 1190


View Profile
« Reply #6 on: February 28, 2023, 08:18:23 AM »
0

Very flash indeed Wasim


Sent from my iPad using Tapatalk
Logged
Wasim
Full Member
***
Offline Offline

Model: FC
Posts: 145


View Profile
« Reply #7 on: February 28, 2023, 11:35:10 AM »
0

Just about finished rolling around on the garage floor - only the fuel tank and exhaust to go.




Sent from my iPhone using Tapatalk
Logged

South Australia
FireKraka
Senior Member
****
Offline Offline

Model: FC
Posts: 649


View Profile
« Reply #8 on: February 28, 2023, 03:17:09 PM »
0

Very nice Wasim
Logged
Errol62
Guru
*****
Offline Offline

Posts: 1190


View Profile
« Reply #9 on: February 28, 2023, 09:27:27 PM »
0

Rear sway bar looks to clear the shocks well. Any details please?


Sent from my iPad using Tapatalk
Logged
my8thholden
nsw-club
Senior Member
****
Offline Offline

Model: FC
Posts: 837



View Profile
« Reply #10 on: March 01, 2023, 07:39:29 AM »
0

what make of shock absorbers have you used ?
Logged

these days i'm half as good for twice as long
Wasim
Full Member
***
Offline Offline

Model: FC
Posts: 145


View Profile
« Reply #11 on: March 01, 2023, 07:42:54 AM »
0

I started with a holden rear bar - can't remember what it was off (?) - anyway I fitted to the rear end with no shockers in place to determine where it would hit the shockers and then with some measurements - a cardboard template - using oxygen acetylene - bend the bar - had to adjust a couple of times.

Once the clearance of the shockers was good I then installs to mounting points to the chassis rails.

Cheers, Wasim

Logged

South Australia
Wasim
Full Member
***
Offline Offline

Model: FC
Posts: 145


View Profile
« Reply #12 on: March 01, 2023, 07:43:36 AM »
0

Shockers are Monroe GT 40's.
Logged

South Australia
Wasim
Full Member
***
Offline Offline

Model: FC
Posts: 145


View Profile
« Reply #13 on: June 02, 2023, 04:13:08 PM »
+2

All the chrome plating has been done - very expensive but very happy. A Class in Lonsdale SA did the chrome work.
All the wiring is finished and tested and the engine is running again.
I’ll put the dash back together next week.
Next job is the body work - a tiny amount of rust repairs needed and a few small dents.

Cheers, Wasim






Sent from my iPhone using Tapatalk
Logged

South Australia
Errol62
Guru
*****
Offline Offline

Posts: 1190


View Profile
« Reply #14 on: June 02, 2023, 06:37:25 PM »
0

They are the best apparently Wasim. Very exciting.

Sent from my SM-G781B using Tapatalk
Logged
blacky
Senior Member
****
Offline Offline

Model: other Holden
Posts: 330

I love YaBB 1G - SP1!


View Profile
« Reply #15 on: June 03, 2023, 11:09:53 PM »
0

 Thats going to be one blinged up ute  Cool I spy a set of Tasman centre caps .........  Wink Grin
Logged

I spent most of my money on beer , fast cars and women - the rest I just wasted.
Wasim
Full Member
***
Offline Offline

Model: FC
Posts: 145


View Profile
« Reply #16 on: June 05, 2023, 09:28:46 AM »
+2

There is nothing wrong with your eyesight!



Sent from my iPhone using Tapatalk
Logged

South Australia
Wasim
Full Member
***
Offline Offline

Model: FC
Posts: 145


View Profile
« Reply #17 on: June 06, 2023, 05:22:03 PM »
+1

Dash is all back together





Sent from my iPhone using Tapatalk
Logged

South Australia
FireKraka
Senior Member
****
Offline Offline

Model: FC
Posts: 649


View Profile
« Reply #18 on: June 07, 2023, 10:09:28 AM »
0

Fantastic work Wasim your Ute is going to look great and that chrome is some bling mate.
Logged
Errol62
Guru
*****
Offline Offline

Posts: 1190


View Profile
« Reply #19 on: June 07, 2023, 08:42:46 PM »
0

Looking bloody stunning Wasim.

Sent from my SM-G781B using Tapatalk
Logged
Pages: [1] 2   Go Up
  Add bookmark  |  Print  

Share this topic...
In a forum (BBCode) 
In a site/blog (HTML)

 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.037 seconds with 20 queries.