FE-FC Holden Discussion Forum
November 25, 2024, 07:59:12 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Are you a member of one of the FE-FC Holden Car Clubs of Australia ? If you are, get access to the Club-Member-only area of this discussion board. Send an IM to the board admin, including your real name and club to get access.
 
   Home   Help Search Calendar Login Register  
Pages: [1]   Go Down
  Add bookmark  |  Print  
Author Topic: Fuel leaking into boot  (Read 3366 times)
DN2168
nsw-club
Senior Member
****
Offline Offline

Model: FC
Posts: 865


See you on the road Skag!!


dean.nommensen
View Profile WWW
« on: July 13, 2012, 09:33:08 AM »
0

Ever since I bought the car it has had a fuel smell in the cabin after it is filled up. I hadn't been able to track it down until yesterday. Where the sender screws into the tank was a puddle of fuel (I had purposely filled the tank really full). I replaced the sender gasket, but the screws seemed to have washers on them with rubber seals that were all broken & split. I put a dob of silicon on the screws before putting them back in, but it has leaked again over night. Would tread tape on the screws help seal them, or can you still buy the washers? I looked on rares but they didn't list them. Any ideas appreciated.

Dean.
Logged
KFH
qld-club
Senior Member
****
Offline Offline

Model: FC
Posts: 683



View Profile
« Reply #1 on: July 13, 2012, 10:01:33 AM »
0

I had a small leak in mine as well.  The cure I used was to cut a new gasket out of gasket paper and give either side of it a coating with a non hardening gasket cement, gave the screw threads a light coating of the same cement and screw it together.  No more problems  in 1300 miles.

Keith
Logged

I was born with nothing and still have most of it left
DN2168
nsw-club
Senior Member
****
Offline Offline

Model: FC
Posts: 865


See you on the road Skag!!


dean.nommensen
View Profile WWW
« Reply #2 on: July 13, 2012, 12:23:02 PM »
0

Thanks for your reply Keith. Just finished putting it all back together (with a mouth full of unleaded). See how it goes now, if it still leaks I may have to organise another tank.

Dean.
Logged
mcl1959
vic-club
Guru
*****
Offline Offline

Posts: 6155


FE's rule


View Profile
« Reply #3 on: July 13, 2012, 04:48:14 PM »
0

None of the silastics are going to work as the fuel dissolves them. The original washers are lead. Keith's solution seems OK with a hard setting cement. I have screws here with good washers for $10 a set.

Ken
Logged
DN2168
nsw-club
Senior Member
****
Offline Offline

Model: FC
Posts: 865


See you on the road Skag!!


dean.nommensen
View Profile WWW
« Reply #4 on: July 13, 2012, 05:59:43 PM »
0

Thanks Ken,
I will see how it goes on the weekend & if it still leaks I will get in contact to arrange a set of screws.

Dean.
Logged
DN2168
nsw-club
Senior Member
****
Offline Offline

Model: FC
Posts: 865


See you on the road Skag!!


dean.nommensen
View Profile WWW
« Reply #5 on: July 14, 2012, 05:18:31 PM »
0

24hrs.....so far, so good Grin
Logged
Pages: [1]   Go Up
  Add bookmark  |  Print  

Share this topic...
In a forum (BBCode) 
In a site/blog (HTML)

 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.029 seconds with 20 queries.