FE-FC Holden Discussion Forum
November 26, 2024, 01:34:36 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Are you a member of one of the FE-FC Holden Car Clubs of Australia ? If you are, get access to the Club-Member-only area of this discussion board. Send an IM to the board admin, including your real name and club to get access.
 
   Home   Help Search Calendar Login Register  
FE-FC Holden Discussion Forum > Technical Board > General Technical (Moderators: RET, Glenn 'Stinky' Stankevicius, gp) > Tightening quarter vent.
Pages: [1]   Go Down
« previous next »
  Add bookmark  |  Print  
Author Topic: Tightening quarter vent.  (Read 2161 times)
Not Happy Jan
nsw-club
Senior Member
****
Offline Offline

Model: FC
Posts: 956


Aussie adventure


View Profile
« on: December 08, 2011, 02:49:02 PM »
0
Is there a method to tighten up the quarter vent so it stays open when you are driving?? Mine keeps on swinging closed.
Nick
Logged
You can never have too many!
Port Macquarie NSW
fe350chev
Guru
*****
Offline Offline

Model: FE and FC
Posts: 2601



View Profile
« Reply #1 on: December 08, 2011, 03:16:16 PM »
0
stop whingeing at least you can drive yours lol.  Cheesy just kidding.

I took the time to take a pic for you. See where the bolt goes through, this clamps the shaft tighter to the rod and the hump think hold it there too. Maybe your bolt is loose or shaft is worn. the other one at the top just locates it and i dont think this end is your trouble.
Logged
Deano

Current Rides: 1958 "Black and White Taxi" FC special Sedan, 1957 FE special Sedan, BA Futura,  2015 VF Commodore, 1956 Austin Tipper Truck
Not Happy Jan
nsw-club
Senior Member
****
Offline Offline

Model: FC
Posts: 956


Aussie adventure


View Profile
« Reply #2 on: December 08, 2011, 03:38:26 PM »
0
Thanks Deano
Will give it a tighten Grin
Logged
You can never have too many!
Port Macquarie NSW
fe350chev
Guru
*****
Offline Offline

Model: FE and FC
Posts: 2601



View Profile
« Reply #3 on: December 08, 2011, 04:00:47 PM »
0
a nice tight fit is what you want.  Wink
Logged
Deano

Current Rides: 1958 "Black and White Taxi" FC special Sedan, 1957 FE special Sedan, BA Futura,  2015 VF Commodore, 1956 Austin Tipper Truck
ACE
Guru
*****
Offline Offline

Posts: 1253


DOH!!!!!!!!!!!! !!!!


View Profile
« Reply #4 on: December 08, 2011, 04:19:33 PM »
0
G'day Nick,
You probably need a new vent pivot kit.
Ebay item number 160445831642
Regards ACE  Cool
Logged
mcl1959
vic-club
Guru
*****
Offline Offline

Posts: 6155


FE's rule


View Profile
« Reply #5 on: December 08, 2011, 05:24:14 PM »
0
More likely is that the spring which surrounds the vent window shaft is broken - very common. New springs are available from R/S
If you remove the bolt and trapezium shaped clamp you should find an intact spring as shown in the photo - I'm guessing you won't.

Ken
Logged
fe350chev
Guru
*****
Offline Offline

Model: FE and FC
Posts: 2601



View Profile
« Reply #6 on: December 08, 2011, 05:30:35 PM »
0
a bit of silver solder would fill it out a bit if its not broken, but thats a bit of a dodgy way. ive seen worse, cardboard etc ha ha.
Logged
Deano

Current Rides: 1958 "Black and White Taxi" FC special Sedan, 1957 FE special Sedan, BA Futura,  2015 VF Commodore, 1956 Austin Tipper Truck
Pages: [1]   Go Up
  Add bookmark  |  Print  
« previous next »

Share this topic...
In a forum (BBCode) 
In a site/blog (HTML)

 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.029 seconds with 20 queries.