|
slim
|
 |
« on: April 02, 2011, 04:03:59 PM » |
0
|
Iv stripped a fibre timing gear on my fc and am in the process of removing the camshaft to replace the gear.. iv removed the engine to do other things as well . I cant seem to get the camshaft out ,, The fuel pumps been removed as has the distributor , The timing case cover has been removed and the 2 locater screws have been removed. Have I missed something , Iv put two screwdrivers in behind the gear trying to prize it out but it feels as if something else is holding it there, Do I need to undo the rockers to remove the camshaft.. ANY HELP IS GREATLY APPRECIATED.. THANKS SLIM
|
|
|
|
|
Logged
|
Im located at Liverpool, NSW
|
|
|
CraigA
nsw-club
Senior Member
 Offline
Model: FC
Posts: 471
|
|
« Reply #1 on: April 02, 2011, 04:16:48 PM » |
0
|
Hey Slim. Loosen off the rockers and lift the pushrods out.
You will also need to remove the sideplate and there lifters.
|
|
|
|
|
Logged
|
|
|
|
|
slim
|
|
« Reply #2 on: April 02, 2011, 04:20:02 PM » |
0
|
Thanks Craig , I thought as much .. CHEERS MATE, Off to get greasy again
|
|
|
|
|
Logged
|
Im located at Liverpool, NSW
|
|
|
|
slim
|
|
« Reply #3 on: April 03, 2011, 03:43:13 PM » |
0
|
Got the camshaft out ,, Thanks Craig  |
|
|
|
|
Logged
|
Im located at Liverpool, NSW
|
|
|
|
slim
|
|
« Reply #4 on: April 29, 2011, 03:46:23 PM » |
0
|
Iv got my new alloy timing gear set for my grey engine and have the camshaft gear on the cam. I have discovered that is is an FB engine so therefore the crankshaft gear does not have the screw holes in it for removal tool used on the FE/Fc crankshaft gear.. My question is that there is a washer of some sort in front of the crankshaft gear that has no Key way for removal, do you need this washer that sits in front of and in fact covers the crankshaft gear..Is it an oil sling of some sort ,, How do i remove it to access the Crankshaft gear for removal.. Im a little bit stuck here ,, Any help greatly appreciated. SLIM
|
|
|
|
|
Logged
|
Im located at Liverpool, NSW
|
|
|
Royal
qld-club
Full Member
Offline
Model: FC
Posts: 145
I love YaBB 1G - SP1!
|
|
« Reply #5 on: April 29, 2011, 07:13:31 PM » |
0
|
Hi Slim Yes you need the oil sling on there , to remove if you lightly tap one end of the key in the crank you will find the other end will start to lift and you should be able to remove it with a pair of vise grips, be gentle, once the key is out the oil sling will slide off hope that helps. Roy
|
|
|
|
|
Logged
|
Just "HOLDEN " on
|
|
|
FC427
nsw-club
Guru
Offline
Model: FC
Posts: 2457
I love YaBB 1G - SP1!
|
|
« Reply #6 on: April 29, 2011, 08:15:41 PM » |
0
|
Slim not cam related  but was told you may have a bellhousing to suit toploader to Holden 6  ?? Thanks FC427.... |
|
|
|
|
Logged
|
As I lay rubber down the street I pray for traction I can keep, but if I spin and begin to slide please dear god protect my ride
|
|
|
|
slim
|
|
« Reply #7 on: May 01, 2011, 10:22:42 PM » |
0
|
thanks heaps roy, and fc 427 i will check about for that bellhousing, you just never know ya luck in a big city. cheers slim
|
|
|
|
|
Logged
|
Im located at Liverpool, NSW
|
|
|
FC427
nsw-club
Guru
Offline
Model: FC
Posts: 2457
I love YaBB 1G - SP1!
|
|
« Reply #8 on: May 02, 2011, 07:58:51 AM » |
0
|
Thanks Slim " Got to love the big city" ....FC427..... |
|
|
|
|
Logged
|
As I lay rubber down the street I pray for traction I can keep, but if I spin and begin to slide please dear god protect my ride
|
|
|
|
