Gertie
nsw-club
Junior Member
 Offline
Posts: 64
Grey & White rooles
|
 |
« on: March 08, 2007, 08:27:37 PM » |
0
|
I have sent vynyl samples from under the back seat to USA & they believe they have an exact match. They are sending samples for approval.
I will probably order the vynyl anyway but would like to know if anybody has details of where you can get embossing done for the back rest of FC seats & door trim.
|
|
|
|
« Last Edit: February 13, 2009, 11:26:11 PM by RET »
|
Logged
|
|
|
|
|
Glenn 'Stinky' Stankevicius
|
|
« Reply #1 on: March 08, 2007, 09:17:51 PM » |
0
|
Do you mean vinyl welding? Where the vinyl is moulded to the trim, usually with a stitch pattern? If so you need to find a trimmer with an RF Vinyl Welder and they are few and far between (in SA at least). Dash Original in Holden Hill SA ( http://www.dashoriginal.com.au/) have a setup to do all of the repro door trims, but I am sure there would be someone in your state similar. |
|
|
|
|
Logged
|
|
|
|
Gertie
nsw-club
Junior Member
Offline
Posts: 64
Grey & White rooles
|
|
« Reply #2 on: March 08, 2007, 10:24:11 PM » |
0
|
Thanks Glenn. The difficult bit is the pattern on the black upper section of the FC backrests. I haven't had any luck yet in NSW or Vic. A special stamp has to be made to replicate the pattern & is apparently quite expensive to build.
Geoff
|
|
|
|
|
Logged
|
|
|
|
fcee
vic-club
Full Member
Offline
Model: FE
Posts: 249
I love YaBB 1G - SP1!
|
|
« Reply #3 on: March 09, 2007, 05:57:02 AM » |
0
|
Did all F.C. holdens have this pattern on the backrest ,as mine does not and I believe it to be original ? thanks Steve .  |
|
|
|
|
Logged
|
Sale Victioria
|
|
|
|
RET
|
|
« Reply #4 on: March 09, 2007, 06:13:50 AM » |
0
|
No, it was introduced during 1959. I went looking earlier to see if I had a good picture of it for the benefit of this thread, but couldn't find one.
Perhaps someone with a '59 FC that has embossed seat-tops might like to oblige?
cheers
RET
|
|
|
|
|
Logged
|
|
|
|
|
sgo
|
|
« Reply #5 on: March 09, 2007, 09:48:56 AM » |
0
|
Wouldn't you know, I took an old backrest to the tip last weekend, and remember thinking as I loaded it on the trailer, "never noticed that embossing before"  |
|
|
|
|
Logged
|
|
|
|
THOMMO_2
Junior Member
Offline
Posts: 80
FB-EK Car Club of SA
|
|
« Reply #6 on: March 17, 2007, 01:10:05 PM » |
0
|
I cant believe in this day & age, people still take old holden parts to the dump  Surely it could have been advertised on this forum as a give-away!!!!! One mans trash is another mans treasure. |
|
|
|
|
Logged
|
USE IT OR LOSE IT
|
|
|
Maco
nsw-club
Senior Member
Offline
Model: FC
Posts: 960
|
|
« Reply #7 on: March 20, 2007, 09:27:14 AM » |
0
|
Yes, I totally agree.
Cheers
John
|
|
|
|
« Last Edit: April 24, 2007, 10:55:21 PM by maco »
|
Logged
|
Better in Green
|
|
|
Gertie
nsw-club
Junior Member
Offline
Posts: 64
Grey & White rooles
|
|
« Reply #8 on: September 04, 2007, 07:36:15 PM » |
0
|
I manufactured the patterns for the seat backs & the first pressing failed due to the vinyl from USA being a little different to the local stuff. I ordered some more vinyl & dropped it off to Polyweld yesterday. Will post the results after the job is completed. I am donating the patterns to Polyweld so he can continue to produce seat backs if it works.
|
|
|
|
|
Logged
|
|
|
|
|
TTV6FC
|
|
« Reply #9 on: September 04, 2007, 09:36:11 PM » |
0
|
Hi Gertie,here's a photo (not a very good one) of one of my seats.Cheers,Jamie.  |
|
|
|
|
Logged
|
Run your fingers over my Holden and I'll run my Holden over your fingers!!!!
|
|
|
Gertie
nsw-club
Junior Member
Offline
Posts: 64
Grey & White rooles
|
|
« Reply #10 on: March 29, 2008, 06:53:42 AM » |
0
|
Polyweld did not want to keep the patterns, so I still have them. They are available for use by club members but a deposit will be required to ensure safe return. Will take some pics today to show the results.
|
|
|
|
|
Logged
|
|
|
|
|
