FE-FC Holden Discussion Forum
November 25, 2024, 08:23:07 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: The FE-FC Holden Car Club of NSW are proud to host the 19th FE-FC Holden Nationals. Check out the announcement video for more.
 
   Home   Help Search Calendar Login Register  
FE-FC Holden Discussion Forum > Technical Board > General Technical (Moderators: RET, Glenn 'Stinky' Stankevicius, gp) > Smiths Beehive heater
Pages: [1]   Go Down
« previous next »
  Add bookmark  |  Print  
Author Topic: Smiths Beehive heater  (Read 7291 times)
ACT59FC
act-club
Full Member
***
Offline Offline

Model: FC
Posts: 130



View Profile WWW
« on: January 11, 2016, 08:29:12 AM »
0
Below Ive attached a pic of two rubbers that attach into a Smiths heater for the ducting. Mine are in pretty poor condition. Does anyone know of a mod or someone who has made up something to replace these rubbers?



Regards Rod.
Logged
FC the Marilyn Monroe of Holdens. All the curves in exactly the right places!
zulu
nsw-club
Guru
*****
Offline Offline

Model: FE and FC
Posts: 1863


Old Boonah Ambo


View Profile
« Reply #1 on: January 11, 2016, 01:52:57 PM »
0

To the best of my knowledge they are not reproduced and it is not often they are still with the heater
So if it was me I'd clean and lubricate them carefully and wrap them in cotton wool till you need them
Logged
ACT59FC
act-club
Full Member
***
Offline Offline

Model: FC
Posts: 130



View Profile WWW
« Reply #2 on: January 11, 2016, 02:47:36 PM »
0
Thanks Zulu, I know there are a lot of people out there with the smiths heaters, how do they direct the heat to the windscreen. (something very important in a cold place like Canberra)
There must be a modification out there somewhere?


Regards Rod.
Logged
FC the Marilyn Monroe of Holdens. All the curves in exactly the right places!
Not Happy Jan
nsw-club
Senior Member
****
Offline Offline

Model: FC
Posts: 956


Aussie adventure


View Profile
« Reply #3 on: January 11, 2016, 10:39:09 PM »
0
I think this is the correct link
http://forum.fefcholden.club/index.php?topic=24309.0
Some one may be able to do it better
Ed Ho used to make them. He is on this site. Hope this helps

Nick
Logged
You can never have too many!
Port Macquarie NSW
ACT59FC
act-club
Full Member
***
Offline Offline

Model: FC
Posts: 130



View Profile WWW
« Reply #4 on: January 12, 2016, 09:59:02 PM »
0
Thanks Nick, I'm only new and don't know how to look people up. I hope Ed Ho reads this post  Grin

Regards Rod
Logged
FC the Marilyn Monroe of Holdens. All the curves in exactly the right places!
Stewy
sa-club
Senior Member
****
Offline Offline

Model: FE
Posts: 881


FErgus 1957 FE Special Station Sedan


Jeff Stewart
View Profile
« Reply #5 on: January 12, 2016, 10:23:46 PM »
0
Ed has not been on here for a while, I will send him a message.

Cheers Stewy   Cool
Logged
No matter how much you push the envelope, It'll still be stationery
Ed
Guru
*****
Offline Offline

Model: FE
Posts: 3311



Ed74mnd
View Profile
« Reply #6 on: January 13, 2016, 11:38:11 AM »
0
Hi guys,
Thanks for the message Stewy!
I made a one off set for beehive to duct adaptors from fibreglass. You just mould the body and vent tubes. Quite a simple job. I can probably post a tutorial on here.

Havent made any vents for some time but will check my molds and supplies... been a bit busy on other projects.
Logged
in the shed
Ed
Guru
*****
Offline Offline

Model: FE
Posts: 3311



Ed74mnd
View Profile
« Reply #7 on: January 13, 2016, 11:40:59 AM »
0
Will look into it.
Just away right now though.
Rod tried to pm you but not sure if it sent. Only have internet via phone.
Cheers Ed
Logged
in the shed
customFC
nsw-club
Guru
*****
Offline Offline

Model: FC
Posts: 5900


Ask me about microwaving cats for fun or profit.


View Profile
« Reply #8 on: January 15, 2016, 10:24:41 PM »
0
Hey Ed.
If you ever knock up another set of beehive heater adaptors, I'd be interested in a pair.
Regards
Alex
Logged
Pages: [1]   Go Up
  Add bookmark  |  Print  
« previous next »

Share this topic...
In a forum (BBCode) 
In a site/blog (HTML)

 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.052 seconds with 20 queries.