|
FB_MAD
|
 |
« on: November 15, 2008, 01:07:21 PM » |
0
|
I need a smallblock pushrod to get a 307 Chev engine running on the shed floor.
Has a snapped pushrod inlet no 5 cyl ATM.
If ( once I get it running ) it turns out to be a good running engine then I'll spend the $$$ and buy decent pushrods and regasket and freshen up the engine.
Anyone sick of treading on old Chev V8 pushrods in their shed??
|
|
|
|
|
Logged
|
Has anybody seen my red pen??
|
|
|
|
FB_MAD
|
|
« Reply #1 on: November 20, 2008, 05:57:18 PM » |
0
|
I'm still looking for a pushrod to suit smallblock chev V8.
Did have some organised via another forum but the bloke couldn't find them.
So am still needing one,
Only need one,
Happy to pay for it and postage cost.
|
|
|
|
|
Logged
|
Has anybody seen my red pen??
|
|
|
CraigA
nsw-club
Senior Member
 Offline
Model: FC
Posts: 471
|
|
« Reply #2 on: November 20, 2008, 07:47:07 PM » |
0
|
Have you tried your Holden Red six ones, I think they are the same.
|
|
|
|
|
Logged
|
|
|
|
|
FB_MAD
|
|
« Reply #3 on: November 20, 2008, 10:05:10 PM » |
0
|
Didn't know they were the same as chev, have plenty of red six parts here so will have a look.
Thanks for the info 70 XU1,appreciate it heaps.
|
|
|
|
|
Logged
|
Has anybody seen my red pen??
|
|
|
CraigA
nsw-club
Senior Member
Offline
Model: FC
Posts: 471
|
|
« Reply #4 on: November 20, 2008, 10:46:07 PM » |
0
|
Even if they aren't the same just grind the red one to the correct length. Or if too short you could make one 'adjustable' by cutting the pushrod, tapping the oil gallery,and then inserting some threaded rod.
|
|
|
|
|
Logged
|
|
|
|
|
FB_MAD
|
|
« Reply #5 on: November 20, 2008, 11:26:54 PM » |
0
|
Yep, I guess thats not a bad idea as I only want get the engine going to see whether it runs any good and has sufficient compression to last for a while.If its any good I'll shout it to a freshen up with some decent parts before it goes in my EK sedan.
Might just cut a red six one and weld it together.
|
|
|
|
|
Logged
|
Has anybody seen my red pen??
|
|
|
|
ACE
|
|
« Reply #6 on: November 21, 2008, 09:04:18 AM » |
0
|
G'day FB_MAD, Holden Red 6 pushrods are too long. I've used 16 V6 Commodore push rods in my small block chev  They are stronger than standard Chev ones  ACE  |
|
|
|
|
Logged
|
|
|
|
|
Ed
|
|
« Reply #7 on: November 21, 2008, 09:22:45 AM » |
0
|
Terry,
Are they similar to Holden V8 ones?
I can measure some up for you. I have a jar of spares I was going to turn into some sort of garage art.
let me know
Cheers
Ed
|
|
|
|
|
Logged
|
in the shed
|
|
|
FC427
nsw-club
Guru
Offline
Model: FC
Posts: 2457
I love YaBB 1G - SP1!
|
|
« Reply #8 on: November 21, 2008, 09:23:22 AM » |
0
|
G'day FB_MAD, Holden Red 6 pushrods are too long. I've used 16 V6 Commodore push rods in my small block chev They are stronger than standard Chev ones ACE Ace how was the length for the Chev  did valve train geometry work out OK if so with what ratio rockers .......FC427...... |
|
|
|
« Last Edit: November 22, 2008, 11:54:16 AM by stinky »
|
Logged
|
As I lay rubber down the street I pray for traction I can keep, but if I spin and begin to slide please dear god protect my ride
|
|
|
|
FB_MAD
|
|
« Reply #9 on: November 22, 2008, 05:24:25 PM » |
0
|
Thanks ACE,
Yep, red six pushrods are approx 9.1 inches or so and from what I can find out chev ones are approx 7.8 inches although I could do a "cut and shut" on the red six rod to shorten it ( I only need one to see how the motor runs,not for normal long term use).
I think I've managed to get some thanks to a generous forum member but I'll chase up some Commondoor V6 ones as a back up if they'll fit.
Thanks ED,
I've got some Holden V8 ones in the shed but from memory they are same length as red 6 ones ??. Appreciate the offer thanks ED.
Appreciate the advice and assistance offered so far by everyone,
Cheers,
Terry.
|
|
|
|
|
Logged
|
Has anybody seen my red pen??
|
|
|
|
