FE-FC Holden Discussion Forum
November 22, 2024, 01:16:43 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Are you a member of one of the FE-FC Holden Car Clubs of Australia ? If you are, get access to the Club-Member-only area of this discussion board. Send an IM to the board admin, including your real name and club to get access.
 
   Home   Help Search Calendar Login Register  
FE-FC Holden Discussion Forum > Technical Board > Restoration Help (Moderators: RET, Glenn 'Stinky' Stankevicius, gp) > Sheet metal question
Pages: [1]   Go Down
« previous next »
  Add bookmark  |  Print  
Author Topic: Sheet metal question  (Read 216 times)
customFC
nsw-club
Guru
*****
Offline Offline

Model: FC
Posts: 5900


Ask me about microwaving cats for fun or profit.


View Profile
« on: November 12, 2024, 11:42:14 PM »
0
Hello brains trust.
Needing to source some sheet metal to do rust repairs.
Not sure type and gauge that I would need.
I would appreciate any advice, best place in Sydney to source what I need would also help.
Regards
Alex
Logged
Jolls
nsw-club
Senior Member
****
Offline Offline

Model: FC
Posts: 258



View Profile
« Reply #1 on: November 13, 2024, 12:10:42 AM »
0
Quote from: customFC on November 12, 2024, 11:42:14 PM
Hello brains trust.
Needing to source some sheet metal to do rust repairs.
Not sure type and gauge that I would need.
I would appreciate any advice, best place in Sydney to source what I need would also help.
Regards
Alex

Hi Alex,

It depends on what you are trying to repair. For panels I tend to use what I can get for free from cars being scrapped. Roofs are a good get as they have a large surface area and complex curves so you can sometimes cut a section to fit with minimal work.

Cheers
Craig
Logged
Cheers n Beers

Jolls
fcute
Junior Member
**
Offline Offline

Model: FC
Posts: 58



View Profile
« Reply #2 on: November 13, 2024, 02:05:51 AM »
0
1.00mm cold rolled mild steel. Rather than buy a whole sheet try a sheet metal shop, for some offcuts.
Logged
Errol62
Guru
*****
Offline Offline

Posts: 1188


View Profile
« Reply #3 on: November 13, 2024, 07:52:07 AM »
0
I bought full sheets of 0.9mm and 1.2mm zinc-anneal.


Sent from my iPad using Tapatalk
Logged
my8thholden
nsw-club
Senior Member
****
Offline Offline

Model: FC
Posts: 836



View Profile
« Reply #4 on: November 13, 2024, 08:02:02 AM »
+1
yes 1.00mm cold rolled from Buttsworths in Windsor ..my panel man was very happy with it ...
Logged
these days i'm half as good for twice as long
customFC
nsw-club
Guru
*****
Offline Offline

Model: FC
Posts: 5900


Ask me about microwaving cats for fun or profit.


View Profile
« Reply #5 on: November 14, 2024, 10:54:14 PM »
0
Thanks for the info and suggestions.
Regards
Alex
Logged
Pages: [1]   Go Up
  Add bookmark  |  Print  
« previous next »

Share this topic...
In a forum (BBCode) 
In a site/blog (HTML)

 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 1.082 seconds with 20 queries.