FE-FC Holden Discussion Forum
November 05, 2024, 08:08:55 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Are you a member of one of the FE-FC Holden Car Clubs of Australia ? If you are, get access to the Club-Member-only area of this discussion board. Send an IM to the board admin, including your real name and club to get access.
 
   Home   Help Search Calendar Login Register  
Pages: [1]   Go Down
  Add bookmark  |  Print  
Author Topic: HR R&P Front End  (Read 4168 times)
sgo
Senior Member
****
Offline Offline

Posts: 444



View Profile WWW
« on: January 14, 2007, 12:44:48 AM »
0

$400.  Pick up Jan Juc. Vic.
HR Front-end with Commodore R&P steering.
Has got:
Excellent turning lock.
Very low km ball joints and bushes.
V6 engine mounts-easily removed if not req'd.
Reinforced bottom plate.
Intermediate steering shaft.
HQ stub axles.- suit commodore or hq discs.
Assistance with details for engineering, and installation provided if required.
Needs:
Some ball joint rubber boots replacing.
Front outrigger to suit your application.
Some welding completed.
Early Torana steering arms-modified taper.
Small spacers machined.
Has been removed from vehicle after doing low kms.


Also available one stock HR drum brake front-end, as removed from original vehicle, assume needs complete rebuild?
$250.
Logged

minifcvan
Guest
« Reply #1 on: January 14, 2007, 12:55:04 AM »
0

THAT IS SO CHEAP......................................
Logged
sgo
Senior Member
****
Offline Offline

Posts: 444



View Profile WWW
« Reply #2 on: January 14, 2007, 01:14:20 AM »
0

I will accept higher offers Smiley
also contact can be made at:
sgomachen (at) hotmail (dot) com
Logged

sgo
Senior Member
****
Offline Offline

Posts: 444



View Profile WWW
« Reply #3 on: January 22, 2007, 09:51:05 AM »
0

in response to questions:

I have spent some time sorting out a power steering set-up and that's is the reason for removing the manual front-end.

I have adjusted the position of the rack mounts to minimize bump-steer and have the mounts tacked in the correct position so the welds need to be completed.

The steering arms are in use on my current front -end. There may be a tie-rod end that suits the Torana arms needed, or othewise the taper will need to be reamed out to suit the the holden tie-rods as I currently use.

The v6 uses the stock oil filter.

It was in my FC that can be seen in the forum pics section as 59v6

The stubs are bare and you will need either HQ or  VPCommodore discs for whichever stud pattern you want to use.

I'm also currently using the top wishbones so the ones supplied do not have new bushes etc.

Logged

sgo
Senior Member
****
Offline Offline

Posts: 444



View Profile WWW
« Reply #4 on: January 30, 2007, 10:38:53 AM »
0

R&P front end sold.
Still available one stock HR drum brake front-end, as removed from original vehicle, assume needs complete rebuild?
$250.
Logged

Russ
Full Member
***
Offline Offline

Posts: 131


mmm dohnuts


View Profile
« Reply #5 on: March 04, 2007, 08:51:08 PM »
0

 :-/will the mounts fit the ecotec v6??? and will vt disks fit???

Oh and where in this wide brown land are you??? can you deliver for that price (about 3000km north of adelaide) Grin Grin
Logged

Ford boy with a FC weakness!!!
Russ
Full Member
***
Offline Offline

Posts: 131


mmm dohnuts


View Profile
« Reply #6 on: March 04, 2007, 08:53:43 PM »
0

sold sorry didn't read propa
Logged

Ford boy with a FC weakness!!!
Pages: [1]   Go Up
  Add bookmark  |  Print  

Share this topic...
In a forum (BBCode) 
In a site/blog (HTML)

 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.047 seconds with 20 queries.