Hello

I have Fc sedan for sale , Shell & most panels have been medial blasted & etch primed ,There is  a dent in roof where sunvisor was mounted , bonnet & 2 boots  good condition, RH front guard ok LH guard not so good , Doors  have some rust pin holes  and dents LH floor panels have large rust holes , RH floor panel have small pin holes , I have 4 new floor panels , Inner & outer sills are good condition , boot floor & inner wells in great condition , I have 90% of chrome work , no motor gearbox diff & front suspension , I have front & rear seats door trims , car is currently mounted on a rotisserie , i also have some parts to modify Hr Cross member , new floor tunnel, Castlemaine chassis kit ( missing front tie plates & mounting bolts)
I can send some photos if you are interested ,

Hello
Just a couple of questions about Front End
Front mount rack or rear mount
is steering column Collapsible & shortened
Regards
Wayne

Hi Luke
I have Fc front end , I live in sydney
Regerds Wayne

hello
we used a some su carbys of a mini 850 of a FJ ute ( there is two different types fuel bowls   , if you live in Sydney there is a leyland wreckers out near milperra/bankstown
Regards Wayne

Hello
I had HR with a HZ dual Circuit master cylinder using a crs mount kit & a HR clutch master cylinder , a vh40 booster, only the front brakes were boosted , HR front disc & HR rear drums ,
REGARD WAYNE

 Hello Weddo
that's  a great looking car you have & it sounds awesome , I was watching it on Gasolene last night , They were showing the Lonford Revival Festival , your car appeared a few times , If no one watch it , its repeated on Saturday 5 pm & next Thursday there will be more of the festival ,
 

Great photo's photo Shayne , the Ute reminds me of a fc Ute from west Sydney in the late 70's early 80's it had 3" holes drill in the inner sills, tailgate drilled also & the car was gutted of all items non essential , running a hot red six . It would lift the left hand front wheel about 2 foot of the ground when it launched,i seen it out at Castlereagh drags a few times
Regards wayne

Hello
Auto one in Forrester rd St Marys is good, Stewart been in the spare business for around 25 years
Rgds Wayne

Hello
I have just started my FC sedan project ,253 with 5Lt EFI heads & carby, i will convert to EFI at a later stage ,T700 gearbox 9" diff ,HR front end with rear rack setup ( i had a front mounted rack on my HR sedan steering was nice,  turning circle was terrible & tire wear was terrible the Ackermann steering geometry was right out , I have contacted few people  Castlemaine  rodshop  have  just made up a new conversion kit for FE & FC with HR front end with rear rack set up to suit 253 & 308 modified HQ sump & pick up ,V6 conversions in Moree also do a set up , Rod rack in Qld only do a front mount rack set up for Holden V8, I would love to get one V6 conversions new front end set ups  but its i little bit to dear at the moment, A LH,LX steering column is not hard   set up,You could fit the column change from torana , the biggest challenge is the linkages & room  in engine bay, you could try Lokar for a cable set up and i think  Flaming river columns have column set up column shift, You should  contact a engineer to find out what you can do & not, I am using Vmc Engineering 0403328574 Sydney based, He has resolved a lot of my query's
 I am going to run HR stubs with P76 disc & HZ calipers to give me a bit more clearance for my wheels, Rear is ford 11" drums at the moment
Regards Wayne

Hello
what clutch fork are you running , I had a HR with a brass button clutch & i kept on bending standard  Holden  M20 & M21 forks i had one made up  , I think my master cylinder had a slightly smaller cup in it ,

Hello
Try J&VR Transmission at forge street Blacktown 0296717904
Regards Wayne

Try Better springs at St Marys

Hello
I am chasing a set of FC Guards & grille for my new project
Regards Wayne

Hello Alex
Are you still chasing a Hr Boot
Wayne

Hello Alex
i live out penrith way & work at chullora , give me a call 0415153245

Hello Alex
I have Hr boot for sale
Regards Wayne