Hi everyone

Spats, whitewalls, electric wiper motors are gone. Someone has a hold on the chrome bits, so most of the "good stuff" has gone.

I'm keen to sell the exhaust system. It came off a FC sedan with a 149 red motor from engine pipe to tailpipe incl muffler, its new, make an offer

Thanks

Tony
0402 891 337

Hi everyone

I'm moving overseas for a few years at the end of August, and need to clean out the garage.

Sorry, I don't have time to pack and ship/post anything, so pickup from Castle Cove only (North Shore in Sydney). Please also call me on my mobile 0402 891 337, I may not check the forum all that regularly. Sorry for all the conditions, but I'm a  bit pressed for time with lots to do and anything I don't sell is going into storage.

I've got loads of "stuff" all of it for FC will try to list most of it below, but if there is anything you need let me know. All pricing is fair and negotiable

Original rear wheel spats. Okay condition, I paid $150 for them years ago
Set of four ATLAS flapper white walls. Brand new haven't taken them out of the package, paid $150
Chrome bonnet hinges, no springs but you shouldnt chrome them anyway (never fitted) -  make an offer
Chrome front stabiliser bar (never fitted) - make an offer
Complete standard steel exhaust system, end to end incl muffler - make an offer
tri matic transmission, not sure of condition but I think it will be okay $5
EH sump and pickup paid $50 for it years ago
old starter motors and generators, condition unknown $5
loads of taillights, lenses
I have a couple of really good condition original surrounds for the ignition/wiper/choke etc - make an offer
heaps of trim bits in varying condition
really good set of 13 " chrome wheel trims
A couple of Electric wiper motors condition unknown
the rest is odds and ends, not sure what I might find....

Cheers,

Tony


 

I'm cleaning out the shed (again) I've had a tri-matic auto fsitting around or years, havent ever used it and dont have any immediate plans. When I purchased I was told it worked ok, but no way of knowing for sure. Free for pickup from Castle Cove (North Shore in Sydney)

Tony 0402 891 337

Hi Retro

Castle Cove is near Chatswood on the North Shore in Sydney. Cheers

Tony

Hi there

I have a spare set of FC/FE wheel arch spats for sale. They are original, pretty good condition, one of the brackets missing and has a hole in eack one where it looks like they were screwed into the guard? I had this set and a repro set, the repro was easier to spray and finish so I have no need for this set. But if you want original, then these are for you !! I paid $150 for them a few years back, looking for the same price. Pick up in Castle Cove Sydney much prefered, I really dont want to pack and post if I can avoid it....slack I know.... Call Tony 0402 891 337. Cheers

Tony

Hi everyone

Nice new site RET

Is the club participating in the All Holden Day this year? I cant see anything here on the site? thanks

Tony

Hi everyone

I have recently tracked down and purchased our grandfathers original HD Premier, it left the family 14 yrs ago and has taken me 4 yrs to find. So pretty happy, and luckily it is still pretty original but a little worse for wear than when it was last seen in 1993.

Anyhow, I'm on the collection trail for HD bits and pices, it is green on white with brown mokkoride interior, and very standard. I need pretty well everything, there is a lot of repro stuff out there, but I'd rather find some good orignial NOS gear if I can.

So if anyone has any HD/HR bits that they want to unload, please let me know. Eg:

Nasco accessories
Original parts of any type
interior/trim
ARMRESTS !! any colour, just good nick
dress rims, mud flaps


double pulley and fan for power steering (I have the rest of the kit)

Look forward to hearing from you. Thanks

Tony
tjmudie@optusnet.com.au
0402 891 337  

Thanks guys that explains it.....

Tony

Hi All

I had a Air Chief radio restored a few years ago but have only just fitted it. I've tried a few locations for power and earth but the radio isbt working. I'm either doing something wrong or it dud. Can anyone advise the best locations to source/connect the active and earth? Thanks

Tony

Thanks Rusty, perfect, just what I needed to know. Cheers

Tony

Hi All

One more request......

Does anyone have pics of where they mounted the seatbelts on the rear parcel shelf and any advice? Thanks

Tony

Thanks Rusty, appreciate it

Tony

Hi John

Rubber seal arrived yesterday, will fit it up today. The part number and description is

241.050 Mounting Rubber U section 16mm High

I bought 3 metres at $4.35/M

Cheers

Tony

Hi John

Sorry dont know the number (yet) I ordered over phone, gave my VISA and hopefully it will arrive any day soon.....when it does arrive, if the part number is on the docket I'll definately let you know. Cheers

Tony

Thanks to everyone who replied. I ordered some through Spectrum here in Sydney

Tony

Hi All,

My seatbelts arrived back from Perth today and I am VERY happy with the job they have done.

Am going to fit them this weekend, lap/sash front and rear; four in total. I have decided to drill right through the B Pillar; I figure that was the way they were installed back in the 60's so good enough for me and for authenticity.

If anyone has some tips, tricks, things to watch out for I would greatly appreciate (before I start drilling) How far up the pillar, etc. Also if anyone has some basic intstructions? I am going to set to work using a commonsense method, but once I've drilled its too late, so any advice welcomed. Thanks in advance

Tony
tjmudie@optusnet.com.au

Hi All,

Does anyone have a set of original or repro rubber seals that they could take a pic of, measure, or both? I didnt do any good at Clark Rubber, Rares said that they probably have something but would need a sample and/or measurements before they go out the back and look for the stock. Thanks in advance,

Tony

Thanks Craig/Brad. Will give Rares a call. Thanks

Tony

Hi All,

Just been to Repco for brake master and wheel cylinder rubber kits and they claim they cant get the rear anymore. Who do you recommend I source these kits from? Rare Spares? any other recommendations. Just want to save a lot of running around if I can. Oh, and in Sydney. Thanks

Tony

Thanks Richard. Will go buy one, I didnt think they were that easily available. Thanks for the offer

Tony