FE-FC Holden Discussion Forum
March 29, 2024, 07:16:26 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: Are you a member of one of the FE-FC Holden Car Clubs of Australia ? If you are, get access to the Club-Member-only area of this discussion board. Send an IM to the board admin, including your real name and club to get access.
 
  Home Help Search Calendar Login Register  
  Show Posts
Pages: [1] 2 3
1  Technical Board / General Technical / Re: front sills where y frame bolts on on: August 01, 2002, 07:27:24 AM
Just adding on what FCVAN said i think youll find that the mud getting flicked up off the tyre's once stuck in those area's hold's the moisture and then you get the huge amounts of rust that you see.
When i did mine recently i had piles and piles! of dirt coming out of all the thing (i should have put in jars and sold as NOS dirt! Grin Grin)

REGARDS
MIchael
Cool Cool Cool
2  Technical Board / Modification Help / Re: 202 4 186 on: August 01, 2002, 07:19:56 AM
Thanx for the help fella's i was just curios as for the 192 option i might consider something like that once the car is on the road.
Thankyou for the website RET (i didn't type in .vic when i tried to find it) im sorry for taking your one minute Cry if it bothers you so much to answer a simple question however, then i will search else where Wink

REGARDS
Michael
Cool Cool Cool
3  Technical Board / Modification Help / Re: 202 4 186 on: July 31, 2002, 08:21:07 AM
does anyone know the website for vicroads Huh Huh

thanx
Michael
Cool Cool Cool
4  Technical Board / General Technical / Re: front sills where y frame bolts on on: July 31, 2002, 08:11:12 AM
Hi Brad,

I know when i pulled off the front gaurds on my fe ute i found exactly the same thing. The sub frame was ok in that section but just after the end of the sill i have big holes. the previous owner has tried to reinforce the area by adding boxing to hold the bolts for the sub frame. But the whole things rusted pretty bady and it was quit a job to get the sub frame. After some grinding, beltin of the hammer and chisel i finally go the bolts out.

Otherwise though the rest of the car isn't in too bad a  condition  

Hope that helps
it's just my experience though

REGARDS
MIchael
Cool Cool Cool
5  Technical Board / Modification Help / Re: Ej Tongue on Hr Crossmember on: July 31, 2002, 08:01:40 AM
Thanks for that clarification ken i will now endeavour to find  the right sway bar you don't know where i could get one locally do u?


REGARDS
Michael
Cool Cool Cool
6  Technical Board / Modification Help / 202 4 186 on: July 30, 2002, 05:09:09 AM
I was wondering if it is possible to change over a 202 if the car already has a 186 without getting a engineers cert. If the car has already had one for the 186. Also i was told that if the car has been registered in the past with the modified motor ie, a 186 then u don't need to get another engineers cert. is that true and how do i find out the registration history of the car?

REGARDS
Michael
Cool Cool Cool
7  Technical Board / Modification Help / Re: Ej Tongue on Hr Crossmember on: July 30, 2002, 05:01:30 AM
Thanks for that Michael,
Its an fe sway bar does that matter or do i still have to change it to an EJ.


REGARDS
Michael
: Cool Cool Cool
8  Technical Board / Modification Help / Re: Ej Tongue on Hr Crossmember on: July 29, 2002, 07:02:41 AM
Thanks for the advice,
Now im left wondering how is the best way to remove the tongue and how do i get it back on. Huh Huh Huh

Thanks Again
Michael
Cool Cool Cool
9  Technical Board / Modification Help / Re: Ej Tongue on Hr Crossmember on: July 26, 2002, 06:44:44 AM
Great fellas,
Ill pick up the ej tongue that has been offered to me. I wanted to know because i have to actually take it off my mate's car so i didn't won't to go to all that trouble for nothig if you know what i mean.

REGARDS
Michael
Cool Cool Cool
10  General / General Board / Re: RARE SPARES REAR QTR PANEL on: July 26, 2002, 06:38:29 AM
I realise this and i have a printed catalogue in front of me but it is rather difficult to follow. I was hoping someone could tell me. However thanks for you time Brendan


REGARDS
Michael
Cool Cool Cool
11  Technical Board / Modification Help / Ej Tongue on Hr Crossmember on: July 25, 2002, 08:17:17 AM
Hey guys,

I was speaking to ken yesterday and he said that when the hr front end was installed on my ute they guy who did it didn't change the tongue that joins up to the crossmember with one that came off and eh or ek. What i was wondering was is an ej one exactly the same or is it different.


REGARDS
Michael
12  General / General Board / RARE SPARES REAR QTR PANEL on: July 25, 2002, 08:01:34 AM
Hey Guys

Just wondering if Rare Spares sell a rear ute qtr panel that extends above the wheel arch.

Thanx again
Michael Cool Cool
13  Technical Board / Modification Help / Re: Front sub frame on: July 21, 2002, 12:14:17 PM
Apreciate that Ken,
I will be in touch early next week and hopefully we can tee up something.


Thanx to the other fella's as well for the advice, much apreciated.
REGARDS
Michael
Cool Cool Cool
14  Technical Board / General Technical / Re: just like... A pig on a spit on: July 19, 2002, 06:56:48 AM
Hey Guys
Just reading here about your rotiserie sounds great if you can get it to work for you. Good Luck! But on another note though i think you will find that the 'rivnut's' that u are talking about if i understand correctly are actually called nutserts and they are installed with a nutsert gun.
Hope im right and i hope that helps if you are looking for them.

Good Luck with the rotiserie!
Michael
15  Technical Board / Modification Help / Re: Front sub frame on: July 19, 2002, 06:41:59 AM
 Huh Huh Huh Huh Huh Huh Huh Huh Huh Huh Huh Huh Huh
Ok thanks for that
Now it seem's i face quit a problem because i need both top and bottom (i can stick my fingers through one side and and out the other in both corners.
So if i need to make the top sections myself, what's stoppin me from remaking the whole thing myself. I realize you probably can't so how do i go about making the other two top sections.

Thanks Once Again
Michael Cool Cool
16  General / General Board / Re: Paint stripped on: July 19, 2002, 06:30:56 AM
Thanx for the advice fellas
i spoke to ricki (the panel beater) yesterday and he said to leave the ute in the original undercoat. And then as he repairs it he will take it back to bare metal and then spray it in a coat of undercoat.


REGARDS
Michael Cool Cool
17  Technical Board / Modification Help / Centre Console in Ute on: July 18, 2002, 08:03:40 AM
Hey Guys,
As i gutted the interior in the ute on the weekend i was thinking of putting in a center console that would suit a 4spd and also look good
wondering if it's been done before and what's sought  of console should i use.

REGARDS
Michael
Cool Cool Cool

18  Technical Board / Modification Help / Re: Front sub frame on: July 18, 2002, 04:43:10 AM
Ok i have looked on the website ah i found the section but i amm unsure of the three pieces that i need
i need the left and right rails that run parralell to each other which then come up to the piece that runs parrallel with the bumper bar at 90 degree's (the third piece that i need
So my question is which three pieces is it?
And what do i do with them when i get them do they need to be welded in the same fashion as what the old ones were or....? How far back does the rail extend....?

RUST REPAIR FE-FC SUBFRAME & BODY
Part # Description Price UOM
RP10 SUBFRAME LEG FE FC FB EK OUTER RIGHT HAND $75.90 EA
rp11 SUBFRAME LEG FE FC FB EK INNER LEFT HAND $87.29 EA
RP12 SUBFRAME LEG FE FC FB EK INNER RIGHT HAND $82.23 EA
RP20 UNDER BODY CROSSMEMBER SECTION FE FC FB EK $27.59 EA
RP31 SUBFRAME FRONT MEMBER FE FC FB EK LEFT HAND $75.66 EA
RP32 SUBFRAME FRONT MEMBER FE FC FB EK RIGHT HAND $75.66 EA
RP64 SUBFRAME TIE MEMBERS FRONT FE FC FB EK $92.35 EA
RP9 SUBFRAME LEG FE FC FB EK OUTER LEFT HAND $75.90 EA


Grin Grin
I thought i would put the list in so then i know exactly what to order preston is a long way to go for me

THANKS FOR THE HELP ONCE AGAIN FELLA"S
Grin Grin Grin Grin Grin Grin Grin Grin Grin Grin Grin Grin Grin Grin Grin Grin Grin Grin Grin Grin

Ill keep the questions comin and if you guys can keep the answers comin there will be a p-plate fe ute on the road some time next year
thanx once again

REGARDS Michael Cool Cool
19  Technical Board / Modification Help / Re: Front sub frame on: July 18, 2002, 04:03:36 AM
beuty
thanks for the help fellas

REGARDS Michael
20  Technical Board / Modification Help / Re: Front sub frame on: July 17, 2002, 08:12:38 AM
Thank's for the advice

How can i get in contact with the guys at Hadfield and any idea on what there worth???

Does anyone out there have one already that would consider selling it?

REGARDS
Michael in Melbourne
Pages: [1] 2 3
Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.031 seconds with 17 queries.