fat boy
i had an fc ute with efi 5lt and i used a 5 core radiatot and had twin thermos mounted on the outside and still had 20mm clearance
brad

THANKYOU JOHN I TAKE THAT AS A COMPLIMENT AS THEY ARE MY PLATES AND WILL BE SOLD WITH A RESONABLE OFFER
BRAD

JOCKSTER
THE T5G BOX (VKGPA & WALKINSHAW) ARE THE ONLY V8
BOX THAT RAN A FINE SPLINE FRONT SHAFT AND ALL GETRAG (VS S2 AND VT).ALL AUSSIES ARE COURSE SPLINE,THERES EVEN AN M19 BOX (1 TONNER).M20 AND M21 ARE DIFFERENT RATIOS SO U CAN'T PUT A M21 FRONT SHAFT IN A M2O BOX WITHOUT SWAPPING THE CLUSTER.
EASY WAY TO TELL ALL M21 BOXES HAVE TWO LINES ON FRONT SHAFT,M20 HAVE 1 AND M19 HAVE NO LINES ON FRONT SHAFT.V8 AND SIX ARE THE SAME BOX EXCEPT FOR LENGTH OF FRONT SHAFT.EXTREMLY RARE TO FIND A M21 SIX BOX,USUALLY SLR TORANA,XU1 M19 BOX IS USLESS RATIO WISE
BRAD

I HAVE A SET OF NUMBER PLATES FOR SALE.THEY READ FCHLDN AND THEY ARE NEW SUIT VEHICLE IN VICTORIA
AND THEY ARE $1000 DOLLARS
BRAD

This topic has been moved to [link=http://www.fefcholden.org.au/cgi-bin/yabb/YaBB.cgi?board=p4sale;action=display;num=1041230492;start=0]Parts For Sale[/link] by RET.

ED,EVEN IF YOU USE VT 5LT MANIFOLDS THEY STILL WON`T BOLT UPTO YOUR HEADS BECAUSE ALL 5 LT INJECTED EXHAUST PORTS ARE IN DIFFERENT POSITIONS TO THE EARLY HEADS.AND TAKE IT FROM ME THERE IS NO ROOM FOR ANY STANDARD MANIFOLD TO EXIT WITHOUT HITTING EVERYWHERE(BELIEVE ME I TRIED)SORRY TO DISSAPOINT YOU
BRAD (FCV8UTE).
PS IF YOU ARE HANDY WITH A TIG WELDER AND A BLO TORCH U ARE BETTER OFF BOLTING YOUR ENGINE TO AN ENGINE STAND AND BUYING A BAG OF MANDREL BENDS FROM ANY EXHAUST SUPPLY WAREHOUSE AND MAKE  ;)YOUR OWN BLOCK HUGGERS.THEN THEY`LL FIT

JUST WONDERING IF ANYONE CAN GIVE ME ANY INFO ON MY FC UTE.I HAVE TWO SETS OF TAGS ONE BODY NUMBER IS FC/2106-4004M TRIM 351-651 PAINT NUMBER 256-2031,THE OTHER IS FC2106-9239-S WITHE THE SAME TRIM CODES AND PAINT AS THE OTHER ONE
BUT THE NUMBER ON MY R/H SKIRT IS45895 S
THANKS   BRAD

In Follow Up to Eds Comments They Told Me I Wouldn't
Get The Pipes Out Through The Rails Either But I Proved Them Wrong. Looks Like Youve Used A Hadfield F/End
Ed.Unlike Ed I Left The Engine In The Orginal Position;But Widend The Rad Support Panel And Hid The
Rad Under The Bonnet Locking Panel And Cut The Support Bar Out That It Bolts To.Again Personal Choice.
Ive Had An Fc That I Fitted A Chev Small Block And This Time 5lt And Found The Injected 5Lt A Easier Fit (Photos On This Site.
Brad

thanks jason for putting my pics on this site.he is right in saying not much has changed in 8 months but ive now come to the stage where it needs a cash injection again adding to that fact im building a new garage and landscaping the back yard ive had to put the cover on the ute for a while.no good rushing things and stuffing them up when you have other projects on the go.but what you see is 6 months work and probably another 4 months to go.believe me jason i can think of nothing better than driving this car around when its finally finished. thanks again jason
PS STILL THINK YOU SHOULD HAVE GONE THE INJECTED 5 LTR INSTEAD OF THE SIX.
BRAD

sorry i just looked at the right hand binnacle again
it has cruise but no aerial as someone has pointed out
i can supply the aerial up and down buttons and the l/h hsv binnacle and cluster if required as i said before to make a calais dash work.pretty easily
brad

just looking at the r/h binnacle switch it isnt berlina
because all berlinas had cruise.ican supply berlina r/h
binnacle switch.i can also supply l/h trip computer biinacle and that will allow a calais dash to be wired up
with a patch harness i have. i can even do it for u if you are in melbourne.call brad at commwreck on 03 9330 3600

YES THEY DO JASON