Time to clear out some parts.

I have a complete disc to disc HR Holden disc brake front end with calipers.

$400.00

Located in Thomastown, Vic.

Contact Steve on 03 9404 3150.

Car is now sold, very sorry to see it go.

Steve...

Unfortunately I'm no longer able to drive my much loved FC due to medical problems.


It will come with a RWC and has VIC reg I959FC, $13,500.

More details and photos are here.

[Holden EJ 1963 manual Sedan $10,600.00]

Holden EJ 1963 manual Sedan $10,600.00

Nice unmolested clean early Holden with Grey 138 ci motor, it has mag wheels and also comes with original steel wheels and hubcaps.

The car is registered to December 2011 and has a Victorian RWC

General Information

Car drives like a 1963 Holden should, the brake booster makes the brakes excellent. The EJ runs happily on 91ron unleaded fuel, without the need for lead additives due to new hardened head seats.
I have spent over $3500 on mechanicals to make this car reliable and fun to drive.

New parts.

Radiator core, Top and Bottom Radiator hoses, Heater hoses. Thermostat housing, Thermostat, Radiator cap, Fan belt, Brake booster, Master cylinder, Slave cylinders, Brake reline, Machined brake drums, Brake hoses, Spark plugs and Leads, Electronic distributor kit, Coil, Four shock absorbers, Muffler, Tail pipe, Fully reconditioned Head with Hardened Seats, Valves and Guides, Rear Shackle Bushes, Handbrake cable, Indicator Flasher can, Wiper rubbers, Clutch and Brake Rubbers, Indicator and Stop light lenses, Floor Carpet (Knox carpets), Rust Repairs and paint, Wheel alignment, Windscreen Washer kit (wired to wiper control )

The car has had new floor pans fitted at some stage and is almost rust free, there are some small bubbles on one rear wheel arch only.

Everything works on the car, it will be sold with a full Victoria RWC.

The are two bad points, a small tear in the back of front seat, and the rear seat has some splits which will need redoing, otherwise, it’s all done ready to just go cruising and enjoy.

Car can be viewed at Melton or I can supply photos on request.

For more information ring Graham 03 9743 2276 ( Melton. VIC )

I'm looking for a complete (with the small arms still attached) EK electric wiper motor for my FC.  Please pm or ring 0408 051 751 if you have one for sale.

Steve...

Pm sent.

Steve...

Thanks ratbox, I've sent you a pm.

Steve...

Hi, would you have a repairable drivers side front mudguard available in the parts?  I need one to get my FC back on the road.

Steve...

Hi, 

I'm after a complete EK automatic steering column and also need a good (repairable) drivers side front mudguard to complete FC rebuild (thanks Ken) following accident damage .

I'm in Melbourne and happy to consider any available.  Please PM or ring 0408 051 751

Steve...

Hi, I need a good (repairable) drivers side front mudguard to complete FC rebuild (thanks Ken) following accident damage , I'm in Melbourne and happy to consider any available.

Steve...

Hi Daz,

I have a lot of stuff and I've emailed you the particulars.

Regards,

Steve...

Hi Brad,
Got the car on the road ok, it was all finished except for some minor interior trimming, it was looking real good.

But on the 9/11, I had just washed the car to get ready for a Vic club run the next day, and took it for a drive around the block to be sure it was dry.  

200 metres fom home a guy in a new Magna decided he wanted to drive on my side of the road as well as his.  Resulting in one very badly stuffed Magna and a very sick and sorry fc.  

It wasn't too bad until they had to cut me out of it and took out most of the drivers side of the car.  

My wife and I are pretty busted up and are still in hospital and look like being here for at least a few more weeks (7 down and still counting).

If it wasn't for bad luck I wouldn't have any.

I can highly recommend Shannons Insurance they have been fantastic, not one problem and they have gone out of their way to assist.

Anyway it looks like I'll have a few parts for sale soon including a fully reco'd 132 with less than 2000 k's on it.

Hope all is well for you.

Regards,
Steve...

Hi Tony,
I have an excellent one for sale, I'm in Vic and I've emailed you the details.
Regards,
Steve...

Mike,
I have a brand new pair from Harrisons for sale, I am in Vic and have emailed you the details.
Regards,
Steve...

Thanks Leigh,

That sounds great, it looks like your original info was on track.  Talk to you more at next Fridays club night.  Once again thanks.
Regards,

Steve...

Hi Brad,

I'ts almost complete, the manifold is the one I got from you.  Its been polished and detailed and looks a treat.  I'm just not sure where to start with the jet sizes.
Hope all is going well with you.
Regards,

Steve...

Hi Everyone,

I'm about to install extractors and a twin carb set up onto a stock 132 and I'm wondering if anyone can suggest the correct jet sizes for the carbs?  

The motor is completely stock and will be fitted with a set of HPC coated Lukey extractors and a high torque twin carb manifold, I have been told that 49 mains and 36 power jets could a good starting point, any other suggestions would be great help.

Thanks,
Ozfueler.

Good point Norm, I couldn't agree more.

This is an invaluable site for all Fe/Fc enthusiasts, the wealth of knowledge and the willingness of members to assist and share their experiences is amazing.

Thanks to all involved.
Steve...

Thanks Stinky,
I'm in Melbourne so it is a little dfficult finding some of the numbers in S.A.
I'm currently trying some removalists without much luck, so I would appreciate it if you could talk to your friend and let me know.
Regards,
Steve...

Hi Norm,
I hadn't thought of that, but it's worth a try on Monday.
Thanks,
steve...