Great idea. Ive checked the main rear window and it has a very faint dot(if it is) over the T.
Checked main rear section and its 330mm high just near the divider strip.
Glenn

I sure the guy fitting it had to redrill the two bottom holes for the dividers
Glenn

Yeah i did. He said no it should be loose then put his hand inside against the window and pushed, the whole window popped out, then goes yeah your right (no shit). His solution was to put sealastic on it which has not improved it at all if snything its worst because now sealastic goes everywhere when i try to get it back in place.

The seal is new and professionally fitted, the fitter actually said it was the easiest one he has fitted so i guess its loose. I will try to upload some photos to show the issue.
Glenn

Hi guys
The glass was fitted before resto so it should be fc glass. Im have to every now and again push the glass and rubber back from the outside in and relip the rubber over the top body lip.
Glenn

Hi guy. Ive had the ute on the road for the last few months but I've been having a problem with the rear screen nearly falling out. Its like the glass isnt big enough allowing the seal to much room to move. Has anyone else had this issue and if so who did you overcome it?
Its a rarespares seal.
Cheers
Glenn

Thanks of that.
Cheers
Glenn

Hi Guy. My engineer wants the brake failure light installed.
Im using a vp master cylinder which has a two pin plug. Im putting in a red led light in the dash. My question is how is this switch wired up?
Cheers
Glenn

Hi. I've got a full  rust free cowl section. Im located near Dubbo NSW.
Cheers Glenn

Thanks Ken. Any idea on the length you got them made to? Also where the right angle fitting meets the line is it still held into position with the retaining clip? If you could post a photo that would be great.
Cheers Glenn

Hi guys. I running vp front discs on the ute and was wondering what hoses others have used from the calipers to the original bracket where it meets the metal brake lines?  My calipers are front mounted if that makes any difference.
Cheers
Fcv8

4hammers is this still available as im very interested
cheers
Glenn

Rickjen
You can fjnd images of one that i built in this post.
http://fefcholden.org.au/forum/index.php/topic,19764.msg119415.html#msg119415
cheer
fcv8

The mounting points depends on if you are keeping the front subframe on. If so you can mount to the bumper mounts if not mount to the bonnet hinge mounts.
Fcv8

Hi guy. I have found out the detail. The bride would like four cars but could get away with two if need be. I asked her which her would prefer either sedans or wagons and she said it doesn't matter as long as they were pretty lol. I replied they are FC or FEs they are all pretty  . She would need the cars in Bowral 14.30 until 16.30 on Saturday 26/9/2015. Could you please PM me with prices and phone numbers if you can do it and i will give you the pickup address.

Cheers
Glenn
 

Thanks guys for you replies. I will get exact details of time and place of pickup and how long you will be needed so you can workout if your available.
cheers guys its very much appreciated
glenn

Hi guys

Its getting close to the date of my sons wedding. The wedding will be on Saturday 26/9/15 in Bowral (southern highlands) NSW.  He is looking for 3 cars, Maco i have sent you a pm. I any could assist i would very much appreciate it.

Cheers
Glenn

Hi guys. Im thinking of selling my VQ 5ltr auto statesman. It runs on duel fuel and it has NSW rego until may 2015. I have owned it for 5 years and it has been a great reliable car as a bonus it comes with either FC0058 or FC350 plates that do not incur a annual fee. The car is located in Dubbo NSW. $2500 ono

Hi all, i know its a long shot but im chasing a passenger side fc ute door & ute fuel tank in good condition. Check you sheds or parts pile and let me know what you have available. Cheers Glenn

Thanks guys, i will be in touch closer to the date. Thanks Alex it still looks pretty good.
Cheers Glenn