|
Title: Engineer Post by: Gordon on May 05, 2013, 09:17:32 PM Hi looking for a good engineer in the sydney area for V8 in FC anyone ?
Gordon Title: Re: Engineer Post by: Crumpsnr on May 05, 2013, 10:29:58 PM You could try
Brian Brady 42673969 0407939216 Last time I talked to him he was based at Thirroul but travelled to Shellharbour to look at my car and give advice and didn't charge because he already had another job down this way and it was on his way. Not sure whether he does work in Sydney but it'd only be a phone call to find out. I found he's very good to talk to, and gave me lots of helpful advice. Martyn Title: Re: Engineer Post by: Gordon on May 06, 2013, 09:13:37 AM Ok thanks for that i will give him a ring
Gordon Title: Re: Engineer Post by: Crumpsnr on May 06, 2013, 07:54:10 PM No worries :) It's been a while since i spoke to him so I hope he works out for you. Regards, Martyn
Title: Re: Engineer Post by: FC427 on May 06, 2013, 08:23:18 PM Robert Elliott is the guy you want real nice guy and easy to deal send me a PM if you want his number .......FC427.......
Title: Re: Engineer Post by: NES304 on May 06, 2013, 08:31:46 PM What are they charging???
Title: Re: Engineer Post by: FC427 on May 06, 2013, 08:38:39 PM What are they charging??? NES FC sedan with v6 conversion, shortened commodore rear end , rack and pinion, collapsible column ,fuel tank swap, seat mounts ,seat belt anchors etc etc he required $400 for the first visit $1200 all up ......FC427......Title: Re: Engineer Post by: brett_f on May 06, 2013, 08:51:27 PM Last one i used that hadnt seen the vehicle before charged me $1500. That didnt include the slight mods he wanted. About the going rate in Vic.
Brett Title: Re: Engineer Post by: NES304 on May 07, 2013, 07:39:37 AM What about NSW pricing?
Title: Re: Engineer Post by: fink on May 07, 2013, 07:49:30 AM What about NSW pricing? So what are you say'n,you did all that work on your car without one!norty boy ???Title: Re: Engineer Post by: FC427 on May 07, 2013, 07:52:57 AM What about NSW pricing? NES $1200 and he is in Sydney ......FC427......Title: Re: Engineer Post by: brett_f on May 07, 2013, 08:19:33 AM Gaz i think you are talking to me. No i had an engineer involved from the start. Just didnt use him in the end as he turned out to be a d**kh**d.
Brett Title: Re: Engineer Post by: NES304 on May 07, 2013, 09:48:44 AM So what are you say'n,you did all that work on your car without one!norty boy ??? I have been dealing with an Engineer from the very start - hence my steering rack mounts are 8mm thick as per my thread (engineer request). However, they are wanting to charge me nearly 3grand for the final tick of approval (but are not charging anything for information and checks in the lead up). Which one is the one from Sydney? Title: Re: Engineer Post by: FC427 on May 07, 2013, 10:22:39 AM I have been dealing with an Engineer from the very start - hence my steering rack mounts are 8mm thick as per my thread (engineer request). However, they are wanting to charge me nearly 3grand for the final tick of approval (but are not charging anything for information and checks in the lead up). Which one is the one from Sydney? Insert Quote Robert Elliott is the guy you want real nice guy and easy to deal send me a PM if you want his number .......FC427....... Title: Re: Engineer Post by: GMB-58FC on May 08, 2013, 05:52:02 PM Rather than start a new thread I hope one of the Tassie blokes spots this and can let me know of a good engineer to use here in Hobart???
Title: Re: Engineer Post by: fe350chev on May 17, 2013, 07:27:00 PM I need one who doesnt mind a can and a yarn in western vic or SE SA
|