|
Title: how to remove ignition barrel ?? Post by: oldgmh on April 07, 2007, 06:41:31 AM Does anyone know how to remove the FC ignition barrel from the dash without having a key.? ??? ???
The key is normally required to put the ignition in the LOCK position for removal. I dont have the key for this one as the dash was a swap-meet pickup. I have tried 5 other holden keys to turn the barrel to lock but they wont work. >:( >:( Interestingly I noticed that the FE/FC ignition switch has the facility for a internal globe, to light up the lock, which is not on later models ie. FB EK etc. thanks. ;D ;D Title: Re: how to remove ignition barrel ?? Post by: Glenn 'Stinky' Stankevicius on April 08, 2007, 10:47:39 AM Quote Does anyone know how to remove the FC ignition barrel from the dash without having a key.? ??? ??? If you are lucky (as I was) the retaining nut can be un-screwed and slips over the key hole with a little persuasion. Otherwise keep looking for that key, or maybe head down to a locksmith if things get desperate. Quote Interestingly I noticed that the FE/FC ignition switch has the facility for a internal globe, to light up the lock, which is not on later models ie. FB EK etc. thanks. ;D ;D One of the perks of club membership is getting access to the "Accessory of the Week" articles that have recently highlighted this accessory. Title: Re: how to remove ignition barrel ?? Post by: brett_f on April 11, 2007, 07:02:05 AM early,
if your in melbourne i can make you a key as i am a locksmith. If not take it to any reputable locksmith that deals with automotive and they should be able to make a key without damaging the lock or facia.If they say they can,t dont waste your time with them and go else where. Regards Brett Title: Re: how to remove ignition barrel ?? Post by: oldgmh on April 11, 2007, 09:15:15 AM thanks brett - i might have to end up taking it to a locksmith as you suggest - i am in brisbane. ::)
Title: Re: how to remove ignition barrel ?? Post by: NES304 on April 11, 2007, 06:51:31 PM Earlee,
Mate i'm in the same place....I cant get my ignition barrel back in. I have a key and three locks too but do you think any fit? I'm in bris so let me know how you go. Cheers Title: Re: how to remove ignition barrel ?? Post by: brett_f on April 12, 2007, 08:33:01 AM early and ness,
I know its a long way but if you want to strip the facia and send it to me or the plain locks i will make you a key no charge but you will have to wear the cost of sending both ways. it is not that expensive if you shop around. email me if you intend to do this. Regards brett Title: Re: how to remove ignition barrel ?? Post by: cruiser056 on April 12, 2007, 06:29:35 PM Hi all,
Does the key fit the door locks? If so just get the key cut for the door lock, saves taking the dash to the locksmith. I have done this several times, any locksmith should have no problem making a key. Even if you are not planning on using the ignition in question, it is always good to have a spare with a key. Michael Title: Re: how to remove ignition barrel ?? Post by: NES304 on April 13, 2007, 06:57:56 AM Whoa...Brett F, Very generous mate and appreciated. I found another barrell and it matches the key that I have but not the door locks so I think I'll just get a second key for the doors.
Only thing I'm missing now is a boot barrell. Maybe I'll have four keys for the car (glovebox too) Cheers Title: Re: how to remove ignition barrel ?? Post by: brett_f on April 13, 2007, 07:25:16 AM ness138,
mate do yourself a favour and take the locks to your local locksmith and have them coded the same. supply them a key that works the ignition for example and have them code the other three locks to that key. it will turn out to be a nightmare to find the right keys especially at night. if you have any problems email me. i would expect maybe $20 per lock x 3 regards brett Title: Re: how to remove ignition barrel ?? Post by: suziecreamcheese on April 13, 2007, 11:54:44 AM locksmith in brisbane try colin at amalgamated locksmiths at newstead near breaky creek
Title: Re: how to remove ignition barrel ?? Post by: NES304 on April 14, 2007, 09:51:51 AM Yeah I think i'll get em done the same as ignition. It'll be easier.
Any one have a boot barrel? |