FE-FC Holden Discussion Forum
June 21, 2024, 01:12:59 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News: The FE-FC Holden Car Club of NSW are proud to host the 19th FE-FC Holden Nationals. Check out the announcement video for more.
 
   Home   Help Search Calendar Login Register  
FE-FC Holden Discussion Forum > Technical Board > General Technical (Moderators: RET, Glenn 'Stinky' Stankevicius, gp) > Rear Shocker Removal
Pages: [1]   Go Down
« previous next »
  Add bookmark  |  Print  
Author Topic: Rear Shocker Removal  (Read 3141 times)
utey
Full Member
***
Offline Offline

Posts: 115


I love YaBB 1G - SP1!


View Profile
« on: October 01, 2011, 09:13:32 PM »
0
I'm sure this is a lot easier than I am making it.
How do I stop the shaft turning.
I can only undo the top nut with a socket so I can't hold the shaft!!!!
Thanks in anticipation.

Nick
Logged
If it was easy would it be so much fun!
FCRB26
Guru
*****
Offline Offline

Model: FE and FC
Posts: 3802


peter.mallaby
View Profile
« Reply #1 on: October 01, 2011, 09:40:48 PM »
0
get someone to hold the shock or if on your own put a vise grip or ratchet strap on it and try that other than that rattle gun if you have one
Logged
http://www.mallaby.com.au
hawk
nsw-club
Full Member
***
Offline Offline

Model: FC
Posts: 231


I love YaBB 1G - SP1!


View Profile
« Reply #2 on: October 02, 2011, 09:24:27 AM »
0
Don't they have a slit where you put a flat blade screwdriver to stop it turning.
Logged
FCRB26
Guru
*****
Offline Offline

Model: FE and FC
Posts: 3802


peter.mallaby
View Profile
« Reply #3 on: October 02, 2011, 06:12:17 PM »
0
But they are down in the whole on the rear so unless you had say a spark plug socked with a hex around the top so you could hold it with a shifter and put a screw driver down the centre?
Logged
http://www.mallaby.com.au
Stewy
sa-club
Senior Member
****
Offline Offline

Model: FE
Posts: 881


FErgus 1957 FE Special Station Sedan


Jeff Stewart
View Profile
« Reply #4 on: October 02, 2011, 06:32:05 PM »
0
The original ones have two flat spots on the very top, but didn't help even with a go through 19/32 spanner.
WD 40 spray and the vice grips worked very well in a very rusty FC station sedan.  Wink

Cheers Stewy   Cool
Logged
No matter how much you push the envelope, It'll still be stationery
utey
Full Member
***
Offline Offline

Posts: 115


I love YaBB 1G - SP1!


View Profile
« Reply #5 on: October 02, 2011, 09:28:43 PM »
0
Thanks for the help.
Took two people, one to undo the nut the other under the car holding on to the top section of the shock absorber.
Just have to get the springs reset and suspension all done.

Nick
Logged
If it was easy would it be so much fun!
Pages: [1]   Go Up
  Add bookmark  |  Print  
« previous next »

Share this topic...
In a forum (BBCode) 
In a site/blog (HTML)

 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.032 seconds with 19 queries.