| FE-FC Holden Discussion Forum |
|
April 19, 2024, 04:20:21 PM
|
|||
|
|||
| News: The FE-FC Holden Car Club of NSW are proud to host the 19th FE-FC Holden Nationals. Check out the announcement video for more. |
| Home | Help | Search | Calendar | Login | Register |
|
71
For Sale and Wanted / Reproduction Parts / Re: Nominations for improved cooling head gaskets - fourth round
on: February 09, 2024, 07:45:04 AM
|
||
| Started by Harv - Last post by Harv | ||
|
Got my gaskets today. Thanks Harv No problem  Cheers, Harv |
||
|
72
For Sale and Wanted / Reproduction Parts / Re: Nominations for improved cooling head gaskets - fourth round
on: February 08, 2024, 02:16:14 PM
|
||
| Started by Harv - Last post by DougT | ||
|
Got my gaskets today. Thanks Harv
|
||
|
73
on: February 08, 2024, 05:29:12 AM
|
||
| Started by oldgrey58 - Last post by Jolls | ||
|
It also looks like the rods need to be ground down so that the chromed mounts can be removed and then the rods re-peened over to reinstall. That is my understanding of how the mounts are removed. I have it on my list to do. Cheers Jolls |
||
|
74
on: February 07, 2024, 10:40:18 PM
|
||
| Started by oldgrey58 - Last post by oldgrey58 | ||
|
Thanks Errol 62,
That will do fine. I'll send a PM. Regards Frank |
||
|
75
on: February 07, 2024, 10:36:16 PM
|
||
| Started by oldgrey58 - Last post by oldgrey58 | ||
|
Thanks Doug, much appreciated.
It also looks like the rods need to be ground down so that the chromed mounts can be removed and then the rods re-peened over to reinstall. |
||
|
76
For Sale and Wanted / Reproduction Parts / Re: Nominations for improved cooling head gaskets - fourth round
on: February 07, 2024, 04:36:58 PM
|
||
| Started by Harv - Last post by Harv | ||
|
Hi Harv, Gaskets arrived in Murrumbateman today in pristine condition. Thank you for your time, effot and patience. Cheers n Beers Craig Welcome Cheers, Harv |
||
|
77
For Sale and Wanted / Reproduction Parts / Re: Nominations for improved cooling head gaskets - fourth round
on: February 07, 2024, 03:58:56 PM
|
||
| Started by Harv - Last post by Jolls | ||
|
Hi Harv,
Gaskets arrived in Murrumbateman today in pristine condition. Thank you for your time, effot and patience. Cheers n Beers Craig |
||
|
78
on: February 07, 2024, 03:01:34 PM
|
||
| Started by oldgrey58 - Last post by Errol62 | ||
|
Got one here. $35 plus post.
   Sent from my SM-G781B using Tapatalk |
||
|
79
on: February 07, 2024, 12:55:42 PM
|
||
| Started by oldgrey58 - Last post by DougT | ||
|
I have recently had to do this. Firstly you will have to remove the bunding by cutting the stitching then the vinyl covering will be able to be removed. Inside you will find a masonite type board that is stapled to the metal sleeve that runs the length of the rod. I found the staples to be made of quite tough metal; however, I was able to straighten and reuse them in order to refix a replacement board (old one had broken away from the sleeve). The sleeve is held in place by what I can only describe as an interference fit on the rod and should be able to be removed by rotating the rod while trying to pull it from the sleeve. Hope this helps Doug
|
||
|
80
on: February 07, 2024, 11:19:44 AM
|
||
| Started by oldgrey58 - Last post by oldgrey58 | ||
|
Hi all,
I'm looking for an FC Holden clutch slave cylinder, part number 7409952, casting number 7409134. I'll be reconditioning it so it doesn't need to be in working condition. Thanks. Sent from my SM-S9060 using Tapatalk |
||
|
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines |
|