The only horn wire clamps / clips I can think of is the one that holds the Hi Note horn wire to the radiator support panel brace as it passes over the radiator ?

Or the the horn fuse holder clamp / clip that holds it in place beside the regulator ?

Let me know if you still require an original sample of the L & R rear bar dust / dirt deflectors.

Cheers, Gary

Gary
I would like to take you up on that offer to supply me with two good second hand rear bumper flaps, I will replace them with new repro ones when we make them.  Please send the rubber flaps to Les McVeigh RSP Australia PO box 10 Mail delivery centre Somerton Vic 3062
Les

I have given the go ahead to manufacture the following

48,50,FJ,FE,FC,FB   7418903   LINK WIPER ON ARM

FE,FC   7410356   TURN SIGNAL LAMP LEAD - THROUGH FRONT FENDER SKIRTS

FE,FC   SP1346   HORN WIRE - THROUGH RADIATOR SUPPORT 1/4"

As well as the headlamp harness sleeve
 
What I need now is better samples to allow us to manufacture them
Les

Hi Graham
Any price yet
Les

Graham
Graham
No problem been there done that I know about suppliers email me if you like at (lmveigh at rsp dot net dot au)

Hi Graham
Any price yet
Les

Graham
Are they made from rubber or a urethane type product?
Les

Thanks Ken
If you don’t know what that horn clamp grommet is then I guess it’s not needed
Les

Ken Mclean
Was kind enough to supplier samples of the following
48,50,FJ,FE,FC,FB   7418903   LINK WIPER ON ARM
FE,FC   7410356   TURN SIGNAL LAMP LEAD - THROUGH FRONT FENDER SKIRTS
FE,FC   SP1346   HORN WIRE - THROUGH RADIATOR SUPPORT 1/4"
As well as the headlamp harness sleeve these have all been sent for quotation

We are still looking for FE, FC   7409515   HORN WIRE CLAMP

I would also like a price on the rubber bumper bar flaps as long as they are RUBBER and not a urethane compound. If not a sample of those would be good

I will add the window channel rubber to the list of parts to make
Les

What about the rubber flap that goes under the rear bumper ?? or does some one make it already  .......FC427.......

I will answer with a few questions
Is there a call for this product?
Is there left and right?
Are they the same on all models sedan ute van wagon?
Does anyone have samples?

We are looking for some samples of grommets hoping someone can help
48,50,FJ,FE,FC,FB   7418903   LINK WIPER ON ARM
FE,FC   7409515   HORN WIRE CLAMP
FE,FC   7410356   TURN SIGNAL LAMP LEAD - THROUGH FRONT FENDER SKIRTS
FE,FC   SP1346   HORN WIRE - THROUGH RADIATOR SUPPORT 1/4"
Also is there any other grommets we should make for FE FC’s or any other parts we should make
Les

Sometimes the standard expected is the Rolls Royce standard and not the Holden standard. We try to make repros as good a quality as we can but to a price that the majority can afford
Les

We finally have a prototype check it out


[Edit: made in-line image rather than link -RET]

Just to let everybody know the FC moulding clip set now includes the clips for the rear diagonal moulding part no. bmc1100

the extra clips are

 7411412           CLIP FC REAR DOOR DIAGONAL UPPER
 7411415           CLIP FC REAR DOOR DIAGONAL CENTR
 7411417           CLIP FC REAR DOOR DIAGONAL LOWER
 7411410           CLIP FC MOULDING REAR 1/4 LOWER  

Les,

When you say "FC Seat Surrounds" as opposed to "FE/FC" is that because they would be black only?

And is $220 the price for all 4 pieces? Or per side? Or upper/lower?

I've made this a poll as well.

cheers
RET

Yes Ret only black and all 4 pieces, thanks for the poll

How much interest would there be in these bonnet inserts at around $120.00 ea

How much interest would there be in these bonnet inserts at around $120.00 ea

We are trying to gauge the interest out there for plastic FC seat surrounds  upper and lower made as per original at around $220.00 per set
Les

Try here     http://www.fefcholden.org.au/cgi-bin/yabb/YaBB.cgi?board=repro;action=display;num=1106000128

This badge is a major concern; it would appear that we have given the manufacturer too much work with all the new products we have been making lately. I should have some news this week.

Russell Thiel former member / President of the Early Model Holden Club of Victoria passed away on 26/4/2006 he will be sadly missed, his funeral is next Wednesday check Mondays Sun for details