Show Posts
|
Pages: [1] 2 3 ... 5
|
1
|
Galleries / Members' FEs and FCs / Re: Number plate covers
|
on: March 28, 2022, 06:41:03 PM
|
Yes billy all the interior is original the outside would be 90% I had to replace both inner and outer sills 3 floor pans..bottom left quarter panel and usual rust around headlights and tops and bottoms of guards I left the little dents and scrapes cause every mark tells a story. Maybe one day when finances allow I’ll do a full respray
|
|
|
6
|
Technical Board / General Technical / Blinking blinkers
|
on: March 15, 2022, 01:00:23 PM
|
Hello all Have a little problem with blinkers I put blinker on for a corner and the one green dash light blinks but when they auto shut off I have the two green dash lights blink at the same time..have checked earths have replaced blinker can could it be in the blinker stalk on the column Thanks
|
|
|
7
|
For Sale and Wanted / Parts Wanted / Drivers side stainless trim
|
on: February 11, 2022, 08:43:13 PM
|
Hi am looking for a stainless trim that goes on top of drivers door the one that runs from windscreen along door and matches up with the stainless on the rear door Willing to pay or trade 2 drivers door trims off an FE Cheers Dennis
|
|
|
11
|
For Sale and Wanted / Parts Wanted / First and Reverse Gear
|
on: December 11, 2021, 05:21:53 PM
|
Would anyone have a first and reverse sliding gear they would part with for holden grey gearbox In the exploded view of the Holden shop manual it’s pictured as number 39
Thanks
|
|
|
13
|
Technical Board / General Technical / Ring sizes
|
on: August 09, 2021, 09:50:19 AM
|
I have a set of 3. 1/16 STD rings What size pistons are these for They came with the car and was told there for the motor that was in it and it’s a B motor Putting the ring into the cylinder to check the gap and the gap looks way to big at least 5mm Pistons have 7406474 stamped on top Thanks
|
|
|
14
|
Technical Board / General Technical / Re: Piston markings
|
on: July 18, 2021, 07:57:53 AM
|
Thanks Vern I’ve checked both pistons with the verniers at the top, at the Gudgon pin and at the bottom and there the same measurements, sat them side by side and heights are the same as well.. the dimple in the middle of the piston with the 7406474 number only but the 7406474 LO piston has the dimple about 1/4 of an inch from the edge of the piston head facing forward.only thing I haven’t checked is the ring grooves like you mentioned to see if there are any extra holes or any small differences..I’m only needing the one piston as when I pulled the motor down every compression ring was broken and on one piston a piece of broken ring worked it’s way up under the other piece of ring and spread the ring groove,straight away I figured the bore would be knackerd but luck was with me there’s not a mark in it Thanks for the info Vern
|
|
|
15
|
Technical Board / General Technical / Piston markings
|
on: July 18, 2021, 06:30:26 AM
|
Hi I have two sets of pistons with the numbers 7406474 stamped on top but one set also has LO stamped just above the numbers..can I mix these to make a set
|
|
|
16
|
Technical Board / General Technical / Re: Dash light problem
|
on: May 27, 2021, 09:01:19 PM
|
Problem solved...after having dash in and out at least six times and just as many new bulbs it turned out to be the globe holder itself...for some reason it seems the bulbs were not making contact with the earth part in the holder..replaced it with a good used holder and now have dash lights...small things cause the most headaches,
|
|
|
17
|
Technical Board / General Technical / Re: Dash light problem
|
on: May 26, 2021, 07:40:52 PM
|
Thanks Ken I tried just pulling the globe holder out until I could just see the light and it is on as with the rest of the dash lights... I have an earth jumper wire onto the body and the dash as it was out..every time I put the dash back in and do the two screws back up again that one light goes out....I’m starting to think maybe a break in that wire that goes to the globe and it separates when the dash is in the right position.. Dennis
|
|
|
18
|
Technical Board / General Technical / Dash light problem
|
on: May 26, 2021, 06:14:27 PM
|
Can something inside these gauges collapse so as the dash light won’t illuminate I have the red lights when I turn ignition on and I have the fuel gauge and speedo lights illuminated and I know the light is working but just not showing through gauge...it’s got me going nuts
|
|
|
19
|
Technical Board / Restoration Help / Re: Wiper shaft bushes
|
on: May 26, 2021, 03:48:29 AM
|
Fraze another good use for the old hinge bushes I found was for the gear linkage rods, I bought the new rubber grommets for the bottom end of the steering column but found they were still sloppy so fitted the old brass bushes in the grommets took all the extra play out of the gear changes, I never throw anything away as you find a use for them eventually
|
|
|
20
|
Technical Board / Restoration Help / Re: Wiper shaft bushes
|
on: May 24, 2021, 04:21:21 PM
|
Hi Fraze When I replaced the pins and bushes in my front door hinges I kept the old brass bushes..I had the same problem when I replaced the vacuum wiper with electric motor...the rubber bushes were perished..I cut the old brass bushes down and used them in the wiper arm holes,I soldered them in the arms and they fit and work well hope this helps Cheers Dennis
|
|
|
|