1281
|
For Sale and Wanted / Parts Wanted / Re: taxi handrail
|
on: December 02, 2013, 09:15:07 PM
|
Haydn, I would be. In either stainless or black/chromed. End plugs may even be available at the hardware. I guess once an accurate jig is made up around your sample, you have a set up for producing any number. Dave.
|
|
|
1282
|
For Sale and Wanted / Parts Wanted / Re: taxi handrail
|
on: December 02, 2013, 01:52:37 PM
|
Haydn, Yes, the cost of chrome is always a more than I expect too. Stainless could be viable. Look fwd to hearing the quote. Bracket shape & angle looks to be the only awkward part. Dave.
|
|
|
1290
|
For Sale and Wanted / Parts Wanted / Rear divider mould
|
on: November 29, 2013, 11:01:51 AM
|
Still after a pair (or even one) of these elusive suckers. If anyone has come across any recently that they wish to sell I would love to hear from you. Dave.
|
|
|
1292
|
Technical Board / Restoration Help / Re: Smiths clock bracket
|
on: November 28, 2013, 04:12:21 PM
|
Ill get one away today for trial fit.
Craig i havent forgot your other parts..
Pete
Pete, If it helps, I can post you the clock I bought from Ken so you can check the fit in your shop. Dave.
|
|
|
1293
|
Technical Board / Restoration Help / Re: Smiths clock bracket
|
on: November 22, 2013, 12:20:41 PM
|
Had a go at tweaking the shot Ken posted but no better for reading a couple of the dimensions, sorry. A fax may not transmit any better even on a fine setting. Enlarging may work though & sending several pages to put together. It's a good diagram, maybe just a couple of closer shots of the measurements would do the trick.
|
|
|
1294
|
For Sale and Wanted / Parts Wanted / Re: Odd pieces gone missing
|
on: November 21, 2013, 05:54:30 PM
|
I went to a local fastener shop and purchased some stainless bolts to attach my bumpers, not original and a little bit of work involved but worth it in my opinion. Depending on the brand you might have file off some letters/numbers, then it's just a few minutes on the bench grinder with a polishing wheel.
And even better in real life. 4 mirror finish bumper bolts in stainless. Thanks for tips.
|
|
|
1297
|
For Sale and Wanted / Parts Wanted / Re: Lenlok 20 handles
|
on: November 20, 2013, 10:09:23 AM
|
Leigh, I managed o find some last week & I believe they were posted early this week. Thanks you for replying, I would have taken them for sure. I know of another member who needs to make up a set. Can PM you both if you like. Dave.
|
|
|
1299
|
Galleries / Project Cars - FEs and FCs Under Construction / Re: FC Ute
|
on: November 17, 2013, 09:40:12 PM
|
I can see you prefer the TIG. Having the knowledge & skills to apply the ideal mix of applications only comes from experience gained over a half lifetime. Something that I've wondered about - how did you calculate the leveraged downward forces on curve where the mount is?
|
|
|
1300
|
Galleries / Project Cars - FEs and FCs Under Construction / Re: FC Ute
|
on: November 17, 2013, 05:47:44 PM
|
Thanks 0.6mm mig wire and a steady weave after about 20 schooners last night theres hardly any material to remove with the grinder.
And all the way into the corners with minimal undercut. Who wants to grinds those hard MIG deposits anyway. Argon mix or gasless?
|
|
|
|