 Show Posts
|
|
Pages: [1]
|
|
1
|
For Sale and Wanted / Cars For Sale / Re: FE Ute for sale
|
on: June 13, 2010, 02:25:22 PM
|
|
Steamman- you beat me to it!
Ute sold on Friday- I have been told to keep an eye on the forum for rebuild pics- All the best Dean.
Thanks to all that enquired-
Cheers-
Mal
|
|
|
|
|
2
|
For Sale and Wanted / Cars For Sale / Re: FE Ute for sale
|
on: May 27, 2010, 11:12:26 AM
|
Thanks for the comments all..... no offence taken ratbox..  I have just dropped the price on tradingpost to $6k- but wont be toooo negotiable past there though. I will be out of town until wednesday night- but if anyone wants to view between now and then - it will be in the driveway, just give me a call for the address. I have just realised that i omitted a pic-the worst sill rust one- drivers side. Have just emailed it to fchoon asking him to post it for me- (Thanks Pete) Cheers- Mal |
|
|
|
|
5
|
For Sale and Wanted / Cars For Sale / FE Ute for sale
|
on: April 30, 2010, 01:54:27 PM
|
|
Hi all,
I have a 1957 FE Ute for sale, moving interstate and it will be a bit impractical to keep.
I will get some pics uploaded following the weekend.
It is reasonably standard, with a little rust coming through in a couple of the usual places (Tailgate has seen better days).
Engine, gearbox & diff has been reconditioned approximately 5 years ago, and minimal miles done since.
Runs, stops (on 4x drums), and even goes around corners!
I am chasing around $8k, but would like some input from forum members once photos are up.
Also comes with spare sills(outer), finned alloy rocker cover, a twin carb manifold.
Keep an eye out for photos after the weekend!
Mal- Black Rock- Vic.
|
|
|
|
|
10
|
Technical Board / Restoration Help / Rebuilding A Distributor
|
on: July 03, 2004, 03:48:21 AM
|
Does anyone know where I can get dizzy springs(in melbourne) to rebuild my 138 unit? I've looked on Rare Spares website- but it looks like they only do them on a full unit exchange basis?  Has anyone had some made up? Cheers- Mal |
|
|
|
|
11
|
Technical Board / Modification Help / Sideplate breather pipe mod.
|
on: June 09, 2004, 11:14:33 PM
|
Has anyone had experience in modifying the breather outlet on the grey sideplate? I was thinking about making up a breather box and pipe to run any oil/fumes back to the carb to burn it- rather than dump it on the ground (or all ove the dist. and engine as my pipe is missing  ) Has anyone attempted this before- or more importantly- is there a better way to solve this problem? Can I get away with simply plugging the sideplate outtlet?? Cheers- Mal |
|
|
|
|
13
|
Technical Board / General Technical / Fuel Gauge Electrical Fault
|
on: January 14, 2004, 03:07:01 AM
|
|
I have a short somewhere in my FE ute fuel gauge circuit that causes the gauge to register full when the break pedal is pushed!
Can anyone suggest a good place to start /technique for fault-finding this?
:-/
|
|
|
|
|
15
|
For Sale and Wanted / Parts Wanted / Subframe Member Wanted!
|
on: September 04, 2003, 08:26:07 PM
|
Does anyone have a passenger side subframe member that they are willing to part with? I need to get my FE ute on the road in the next week or so- and rarespares have been out of stock for more than a month! Cheers- Mal |
|
|
|
|
16
|
For Sale and Wanted / Parts Wanted / Extractors/Headers
|
on: September 03, 2003, 12:58:08 AM
|
|
All the rust is welded up, and motor and 'box are waiting to go back in.........but
can anyone suggest who stocks extractors or headers for a 138 in an FE?
Or what about someone who can make a set in melbourne?
Cheers,
mal
|
|
|
|
|
17
|
Technical Board / Modification Help / Seatbelts into FE ute
|
on: August 01, 2003, 01:01:29 AM
|
|
Hi Folks,
Can anyone offer me advice on installing seatbelts into an FE ute?
Are there any existing point that I can mount them?? I would assume not.
Does anyone manufacture a kit that has pre-fabricated mounting point to weld in- or do i need to make them myself?
I am located in Melbourne.
Any help would be greatly appreciated.
Mal
|
|
|
|
|
19
|
Technical Board / Modification Help / Rusty Subframe, Floor, Tray...............
|
on: July 15, 2003, 08:00:54 PM
|
Hello All, I've been watching for a while, and jumped on in! In the process of negiotiating a FE ute  , with the Gold Coast Chrome in the usual places....... Can anyone tell me where I can source replacement floor and subframe in Melbourne? Any help would be greatly appreciated.......... Cheers! Mal |
|
|
|
|
will be.......
