Thanks Ret,& Nes,had a better read of post & worked it out,app worth the money for posting photos alone.thanks again

Could somebody pls explain how to post photos via tapatalk"I have the IT skills of a caveman"thx Rummy

Rick,I had a look at tail gate & couldn't see a switch as such but window doesn't operate in open or down position only when closed.trying to work out how to send photo via tapatalk but not having any clue on how to send,maybe pm me with your email address so I can try that way.Rummy

Mate I don't know about any safety switch,mine is a hd maybe only a hr thing not sure. Rummy

G'day Rick,not sure if this is the correct spot but above centre console under dash on lip so that switch sits flush with dash. If this makes sense! But could be placed anywhere along this lip.i will upload a photo of mine tomorrow arvo. Rummy

G'day Pete,
Thanks for the info on nutserts, this could be an option as the sub frame itself seems quite good.Half the cause of the problem probably came from using a centre punch & blunt drill bits! worth a try first. I'll have a look at sourcing nutserts from here as there is a good fastener shop in town.thanks for the offer & info.
Greg.

G'day Pete,Excuse my ignorance but what is a nutsert! I'm located in Tamworth
Greg

Thanks Ken for your quick responce, I had my fingers crossed their may have been another way as i have had no dealings with the internals of a sub frame.
Anyhow gives me another reason to TINKER!
The learning continues!
thanks again,the wealth of knowledge on this forum is excellent!!
Greg.

G'day Forum,

PROBLEM: I have broken off one of the bolts that hold the sway bar in place & it sheared off inside the sub frame.Whilst trying to drill bolt out i have pushed remaining bolt & nut inside the sub frame & am now at a loss of how to fix this PROBLEM!!!

QUESTION:Do i now have to cut a hole in sub frame to retrieve & remove this lost piece? If so where's the best place to do so?

Thanks Rummy.

G'day Forum, A bit more info,petrol has an extremely low flashpoint(0.2dc-2.0dc)this is why it will ignite from static electricity!+can disolve glues & perish rubbers. Diesel on the other hand has a flashpoint of somewhere between (60dc-79dc)so a lot safer to use & a very good & cheap PARTS WASHER FLUID.that want harm glues etc.Kero lies in between but closer to the diesel side. Hope this helps a bit.cheers Rummy

Sorry missed the festival,was at the mercy of the work gods over the weekend.Hope to see the FE about somewhere in the future!
cheers Rummy

Hey Pete,when & where is this on in Kurri Kurri. Wouldn't mind having a look, & a squiz at your FE.

no probs one more

Hey snuff,i purchased a venetian blind off ebay about 7 years ago and have not had a drama with it,it fits perfect and is easy to install.Although not sure whether it's the same seller as the one your looking at.I checked my feedback and this ID didn't ring a bell but i got it from a seller in melb.and cant remember his ID.

Hey Niffty, congratulations on your wagon! Totally agree these cars are too lovely to change,they already OOZE style, charm & charisma! Now especially with the new up dated GREY motor & running gear.Top job well done!

options 1 to 5 KEEP IT HOLDEN

Sorry, located Tamworth NSW, car is two tone blue sedan, runs well, drives great, pass any inspection no rust radial white band tyres(computer skills not up to speed on posting photos on this message board but will happily email any photos)

Original condition 1957 FE for sale, $8000.00 (Plates included MY57FE)
Always garaged, well looked after, regretable sale due to other commitments eg: kids with horses and motorbikes no time left for old Dorrie, would like to see her go to a club/enthusiast. Please contact me on 0407 27 3280 (leave message if I don't answer and I will get back to you) or email for photos belindarumsby@bigpond.com
Registered until September 2008