Messages

bump;

Hi all,
was wondering if any body can help me out with a photo of the mounting position for the front brake hose(bracket)the one on the k frame.
i had removed mine quite some time a go to install a hadfield strengthening kit,its been about 2 years so I'm buggered to what(where the correct position is to remount them.

@@@ Thanks for any help in advance,
cheers 
--EK.

THANKS KEN,
I DONT KNOW WHAT I WOULD HAVE DONE WITHOUT YOUR HELP
OVER  THE YEARS WITH MY EK,PROBABLY BE OVER ON THE FB-EK FORUM WITH ALL STINKY'S FRIENDS. ::) ::) lol.
CHEERS--EK.

HI ALL,
I'M IN THE PROCESS OF FITTING A HR FRONT END TO MY EK.
I HAVE A PROBLEM WITH THE SPACER TUBES,I ONLY HAVE HR ONES
AND I HAVE RED SOMEWARE THAT I WILL NEED TO USE THE EK ONES.
CAN ANYBODY GIVE ME THE LENGTH OF THE EK ONES ?
I THINK THE FRONT AND REAR ONES ARE A DIFFRENT LENGTH?
AND ALSO WHAT H/D SWAY BAR WOULD FIT THE EK WITH THE HR F/END?
THANKS--EK

Ace,
The part is a ignition lock. but what i want to know does the part number on the box it come in#2825656 correspond with the lock????.
And its not a lj torana as this lock is a dash mounted one and lj torana are in the column.
Thanks---ek

 Ace,
i know what it is but I'm wanting to know if the part # maches the item.
cheers---ek 

 thanks, fc-427&gp but its not a lj torana it must be eather hk-t-g?

Hi all,
could some one with a masterparts catalogue check out a part number  PLEASE!  for its exact application.#2825656
Thanks.---ek

i bought a acl oil pump rebuild kit, then i bought a whole new hv oil pump, it was a long hard decision between standard and hv, i still have the oil pump kit, if you were close by i would sell it for $30

hi there,
fccool-- is the kit a hv rebuild kit?
cheers--ek

 Hi all,
i'm wanting to know if a hr std pitman arm is the same for hr power steer?
thanks--  EK

 ;D ;D CHEERS  GUYS,
---EK

"jonno"
what i have here is nos lucas headlight buckets with both part numbers and i am not sure what model they fit.
i am thinking ej-eh.
could you please tell me what model did the mounting ring#7406040 fit?
and do you think a mounting ring could be a headlight bucket?
cheers---Ek

Hi all,
could any body with a master parts catalogue look up a couple of part numbers for me(please)
what i would like to know what application  they have,(model they fit) i have the part but with both part#
#7406040
#556057.
cheers--Ek

 Thanks ken!!~ i will give them a go.
cheers-- Ek

 hi all, just looking for some input on chrome platers in melb, dose not matter where just want the best!
cheers
---EK

 "HI ALL" CAN ANY BODY HELP ME OUT WITH WHAT THE ORIGINAL KEYS ARE FOR FE-FC?ARE THEY THE "GM" ONE'S WITH BRIGGS&STRATTON ON THEM?.  THE HEX ONE FOR THE  IGNITION & DOOR AND THE PARE SHAPED ONE FOR THE BOOT AND GLOVE BOX? THEN IN WHAT YEAR/MODEL DID THE  KEY WITH"GMH" ON IT COME OUT ?AS  I AM A BIT CONFUSED OVER WHAT KEYS ARE THE ORIGINALS.
CHEERS- ???
--EK

 hey dr terry thanks for your expert advice on this subject my/our steering problems. lol,  As i said in the previous thread is that i'm fitting a hr power steer unit to my ride.and (i was wondering) in your expert opinion if i fit the 14.1 ratio box would this eliminate/dampen the steering being to light.as i have spoken to a few people and they have said that the hr power steering is to light ,especially on the highway.  cheers------------ekolden

Daz" thanks for the info, did you fit a hr steering box or did you just change the shaft from fc to the hr shaft?.
does a hr shaft fit a fc steering box.? i presume they are the same as a ek? as it would be easier for me to just change the shaft to hr if it will fit. or do i need to fit a eh steering box? so all 3 mounts line up.( and ratio)  i am thinking of leaving it at the same as it is (ekratio?) i think with hr  power steer it would be better as the hr power steering was very light as it was  ,i just found out that here in vic it is e legal to fit up a hr steering box due to them only having 2 mounting positions.
and dose any body know what the shortest column is/ eh or hr or are they the same length???? and ratio's????
what i'm trying to achieve is the shortest column that there is and a steering box that is legal in vic and the ratio i'm not sure as yet ,any help on this subject would be greatly appreciated by any body.  At the moment i'm just tossing around a few ideas .   cheers......Gary.

hi there could any body tell me how much shorter is a hr coloum than a fb-ek one?.and if any body could supply a photo of a ek with the hr coloum fitted it would be greatly appreciated, thanks. to gary.loe@optusnet.com.au

"nothing wrong with the old hair dryer" :-X