Messages

thanks for that FireKraka.

Unfortunately. They are all out of them at the moment.

thanks for the advice Rob

Still looking for Beaver panel.

Anyone know of a good rear it could be cut out of?

no one?  :)

hi all,

It has been a while, so I thought I would write an update.

Since moving to Sydney, the project has taken a lot longer than I would have liked.
Logistically it became very hard to keep momentum and then it didn't help that the guy doing my panel beating could no longer work on the car due to other commitments.
We tried another repair shop, but there was no plan and I ended up getting frustrated paying $$ with no end in sight.
So we pulled the pin and the car has been in storage for the last 6 months.

Thanks to some recommendations from members here, I have now moved the body to Brett @ Concours & Custom Restorations and looking forward to getting the body finished and seeing some paint on it.

We have progressed at little:
- we fitted the trans and engine and did a trial fit, so we could make up a cross brace to hold the rear of the trans.
- I rebuilt the steering column (EK) all new bearings, bushes etc.
- pull apart the HR Front end and got it all powder coated


I still after some panels, which I posted in PARTS WANTED.
http://forum.fefcholden.club/index.php?topic=27826.0

If anyone could help, that would be great.



Stash

*Note - This is my second attempt writing this. I just wrote an update here and wouldn't let me publish and then lost the lot!!

[Boot rear panel for a sedan.]

I am some panels in reasonable condition.

Boot rear panel for a sedan.
The one that has a hole for the petrol filler
It has a 90 bend along the edge.



L & R Boot extension panel.
As you can these are rusted out on mine. (and probably on most)



PM if you can help
thanks all in advance.

Stash

Adelaide
Southern Classics and Customs
Autotransformers (Parafield)
Concours and Custom Restorations (Parafield)

Thanks Stinkster..

Agree. They did Grace’s EK ute spray, and George’s VL Commodore smash repair. Honest, timely and good quality work. Worth the drive out to Windsor.

Cheers,
Harv

Thanks Harv - it is a drive!

Hi all,

Anyone recommend a good panel beater in either Sydney (preferred) or Adelaide
I need one to finish off the body work to get to paint.

I would prefer a quote or at least a loose estimate of work required.

Cheers

John

A good mate.

You dont want to have to sell it after all the work you put in.
Sorry to hear about your wife, hope she is on the mend.

Will try to get to a meeting one of these days ...  :D :D

John

Yeah still required.

Thanks everyone for their posts.

Me.. Been MIA apologies...

Hey Jim,

Just been catching up on your progress.
Retired hey! Great you can help me with my project  ;)

Selling the FC - Please tell me it is not true..

All the best

John

Any chance of detailed photos of the seat belts Ian?

similar to POR-15

I used this to reseal my fuel tank.. like brand new now

http://www.kbs-coatings.com.au/product/auto-fuel-tank-sealer-kit/

looking good...

clay.. so maybe one of these?

http://www.whiteline.com.au/product_detail4.php?part_number=BHR37&sq=8021



Assume the box section gets bolted to the chassis.
Given I am finalising all body work before painting, would it be smart to weld these directly to the body?

Stash

Following this thread and the need for an EK only one.
Seems Whiteline only have 1 model that fits all FC - EH

Will this work?



http://www.whiteline.com.au/product_detail4.php?part_number=BHF4&sq=7138

Also they dont seem to make a rear one.
Does anyone know where you can get them now? (HR/EH diff)

thank Ken...we will see how we go.

Rob, I probably owe you a beer or two.
Hope to see you at the next NSW Club Meeting.

just went through this from start to finish.

Great Story..
Great footage..

John

just found old email.

rotors/discs are also HR.
so XU-1 discs here we come :-)