Messages

Thanks guys, that has helped me alot.!!! i purchased a set of ebay for $200 and it had a list of the service that has been done to it from a carby place! soo good deal! the only thing im worried about, which i think it should be right is, im hoping that the carby closest to the firewall does not hit the fire wall because of its position?.. it looks like it may come very close.! does anyone know, from experience or know of anyone, that this has happened to?.
thanks for that guys... so helpful!

Does anyone know if you are able to get a tripple side draft carby minifold for a grey motor?
and to go with it. the xu1 sidedraft racing stombergs??

thanks .
Eric.

Hey mate!!!

back you on Nigel... that man is truely a top bloke and really knows how to make carbies look and go great!!!! top!!!!

If you need your carbies done go to him, He is fantastic.
Xtreme fuel systems!!!

Credits on the car, you have done a great job!!!!.

thanks mate

Hey

Im trying to put an M20 gearbox behind a grey motor using dellows bell housing, with original engine mounts, in my FC. It looks like it will fit, but im worried that it might not fit in the tunnel.  I was thinking of lowing the motor through the back engine mounts, it would not be too hard but not sure if it will work. Is there any suggestion on what i should do??

thanks

hey guys,

I went to the easter show to see this fantastic display and i was so impressed!!!!! very nice line up. was so keen on those L plates on one of the fc's i wish a had of brought mine with my p plates on it and parked right next to him!!!!

the thing which impressed me the most was the twin carby set up on 2 of the fc's, the orange one and one other i cant remember. they look absolutely amazing im so impressed.

I was also very impressed at the members of the club talking to me. champions.!!!!

well done FE/FC club 2009!!!!

thanks very much mate

hey ret,

if your heading down the the meet on tuesday the 5th, can ou bring me a poster and ill give you the money for it on the spot. is that ok??

thanks mate.

robbo,

i just took the carbies and manifold off and sent them to extreme to get rebuilt and polished and shined and i will be getting them back next friday. the manifold which i have had 3 loops i guess you could call them, and this "pole" (great at using terminoligy i am) goes through these loops on the outside bottom edge of the manifold. ill see if i can find this setup on the internet somewhere and send it to you. damn i should have taken a few picks before i took it down to the carby place. 
but If you ever need to get any carbies looking fantasticly shinny and rebuild this guy does a great job, he can take it back to the brass looking finish or he can make it look like polished alloy. i saw a few which he has done. look amazing, i also took the manifold in to him and he will clean that up too. Great bloke "Extreme fuel systems" look on google.

thanks mate

hey

i was looking at a few of the carby set up's at the easter show of 2 of the grey motors and they were both different to eachother and different to mine. Not sure what a W clip is, but i have a bar which runs along, the bottom of the manifold which has 2 shorter bars which come off this bar and go to arms linking to one carby each and another bar which has a control arm on it which goes to a mechanical accel set up. i find this works really well and that the choke does not effect it. the only trouble i had was that the carvies were not fulli opening. but i fixed that soon enough. 

thanks mate..

would anyone happen to know anywhere who are able work a grey motors head. port polish, open valves etc. who is close to sydney??
thanks

does anyone know the shade of grey the grey motor's original colour is???

adaptor plate or bell housing plate from grey motor to aussie 4 speed or any gearbox which will fit n fc.

carby guy at liverpool?? extreme carbies??

hey is it possible for me to get a dash surrounding?
how wil you get it to me and how will i pay etc???
let me know
thanks
Eric

YOU LEGEND thanks. picking it up tomorrow hopefully

;)

where are you able to get these kits from??

wow im in the same situation

so ken?

does this mean i just go to repco and order an fc dash fascia??? because im happy to have the fc dash fascia chrommed with a new plastic thing?

i spoke to that dude from american auto's homebush and he was saying that the guys who make it are just slack basted and are not making them anymore. but they found another dude that will make it and just as u said, he needs the right mould. but we will have to wait untill all this bullshit passes, and they actually start getting them in.

so can i get it from repco?.

thanks mate.
Eric

hey everyone

looking for dash facia for an fe preferably without the plastic
would love it if it was chrome, but any facia behind the bash and also a glove box lid. again ideal if it was chrome but if not still let me know.
prefered if it was in good condition to be chromed surface rust doesnt bother me, but no major cuts or holes on face.

thanks guys

mate,

do you have a dash facia drivers side for an fe?? without the plastic
thanks