Messages

SELLING ONE HOLLEY RED ELECTRIC PUMP & HOLLEY REGULATER $120.00 FREE POSTAGE WITHIN AUS ONLY , NO OFFERS 0403842746

interested then please ph me as too much to mention , muist be sold asap . ph 0403842746 very cheap 100% rust free , $1800 the lot including motor ect bundaberg 4670 queensland

full set of 60 thou acl pistons 202, 3.3 new in box with rings / gudgens ect $100 + postage // brand new starfire rods - shotpeened $100 + post . first in best dressed , holley red fuel pump & regulater used but good . $100 + post ph 0403842746 must clean out shed asap. will post all items

hi,i recieved the bracket , its excactly the one i needed , thankyou  ;D

sorry about the add not stating all facts . im in bundaberg qld , block is still very tight not to mention there are brand new 60 thou pistons to suit .not sure on crank size anymore - its been here for awhile now just in case i needed a spare my ph - 0403842746

sorry io forgot to add - im in bundaberg queensland - happy to frieght at buyers cost - will frieght rims with or with out tyres , depends if u want tyres with rims . please ph me on - 0403842746 if interested most times of day or night up till 10 oclock  thankyou ;D

hi, selling all my roh steel rims ect - sell as one lot hopefully! . i have six rims that measure 13 x 6 inch & two that measure 13 x 8 inch // so there are 8 deep dish rims all up . + if you want them i have four 205 x 60 tyres to suit the above & two 205 x 65 tyres // all tyres are in rwc & have very good tread . i will not sell tyres unless i sell rims . im looking for a set of dragway style rims in 13 or 14 inch .or any decent style mags to suit my old fc holden !

hi, im selling off my spare engine - bottom end esembly .. 3.3 block with oil galleries enlarged & top decked , counterwieght knife edged crank , starfie rods been shotpeened - radiused - balanced , brand new in box acl race series pistons - rings - gudgens ect , also i have a brand new in box jp h/v oil pump to go with the above . just hone & add new bearings ect - maybe rebalance crank ?  & away u go , this bottom end is simaler to my current race engine that was pulling 12.7 in my lc torana coupe before i fitted in my fc sedan .bottom end only - no top end ect  asking $500 & i will put on frieght truck - no hassles doing that if buyer pays .:o

hi, not sure what its called but im after the clutch bracket that bolts to the bellhousing - the one that the  hyd slave cylinder bolts onto ? . i am more than happy to cover cost of item & postage , im in bundaberg QLD 4670 .thankyou

thanks  fc427 on the brakes ect , if i stay with the hr front end i may go to hq front disks like u say & the commodore diff as well . also thanks to ratbox on his info , for now i will get a torana tailshaft just to get it moving onto trailer .great site & reasonable easy to use for such a old fart like my self . ive tryed to be on other forums [ torana ] ones  but seem to get abused when i ask a simple question! .

thanks for the information regarding diffs ect , i did get a set of deep dish ansen wheels when i bought the car but they did not fit - too wide , so i bought a set of deep dish 6 inch steels, might have to dig up a lj torana housing. or even go the commodore rear end like u suggest . would i be able to fit HQ disk on front easy ? . thankyou for the help .

hi,   do u mean its too wide to fit good rubber - i was told that a EH diff housing is narrower so i could fit wider tyres, or do u mean its too weak . i was only running a banjo rear end in my torana,s , without too much trouble .

hi, im new to the fc holdens , i usualy build lc-lj toranas but now i find them boring after owning so many ,so hoping building a old holden will inspire me again,,  just wondering if there is a tailshaft out of a holden that will bolt straight into my fc sedan fitted with red motor & holden 4 speed box - i am running standard fc holden rear end . im trying to make car look near stock but have my ex race motor in it ,was pulling 12.4 in my lc four door but now i have fitted bigger cam & bigger su,s , have already fitted motor - box ect but need tailshaft . thankyou - wayne

hi, im new to this site but hope to offer some advise - ive been racing - building red motors for around 25 years or more so i have a fair idea what works & what dont , in my latest 192 that i just fitted in my fc sedan i have gone to a very large wade solid cam - i did try a  crow cam but i find them no good - for my use anyway - am running counterwieght knife edge crank , good rods ,acl flat top pistons, very modified high compression yella terra 9 port head - to me these are the best heads to start with ,triple 2 inch su,s , large primary extractors ,straight cut timing gears ,lightened flywheel, 3.9 diff gears ,ect ect , cams usually cost around the $250 mark  , alot more if u want a roller cam package . get yourself a solid grind cam & some good top end gear - hope this helps u out in the cost of cams at least .