Messages

Hi there,

I recently acquired a genuine FE Holden rim (ie rivetted centre and the larger valve stem hole).  The wheel still has a tyre on it and is holding air, the rim hasn't got any damage to the edge, just needs painting (flaking).  Happy to post this with the tyre removed, or pickup from Wodonga VIC.  Phone 0418451665 or reply here.  Happy to listen to an offer on this hard to find item!

Regards

Peter

Wheels are now SOLD.

On offer is a set of 4 Chevoit alloy hotwires with two tyres with legal tread but could be a little perished with age for road use.  The wheels are in good condition but have been stored many years.  Were last fitted to a Torana.  Happy to assist with freight, with tyres removed they could be posted in two boxes.  There are no nuts and only one centre cap.  Asking $175 for the lot.  Please call 0418451665, pm me or reply here.  Items are located in Wodonga.  Pics available on request.

Cheers

Peter

Tis gone, thanks!  ;D

Hi all,

I have a Lucas generator and a Bosch regulator that have been in dry storage many years.  Happy to listen to an offer and willing to post anywhere in Oz.  Please reply here, PM me or call 0418451665 to discuss further.

Cheers

Peter

Thanks heaps Glenn, I appreciate it!  ;D

Peter

$22 according to the Aust Post calculator.

Cheers

Peter

I've tried the FB EK forum with no luck, so here goes!  Does anyone have a disc style speedo head to suit an FB EK (can swap for a FE FC needle style one), and a fuel gauge to suit the FB EK dash, I think FB to EH ones all fit?  Happy to pay postage as I'm in Wodonga VIC.  Please pm me or call 0418451665 if you can help.

Thanks

Peter

Not close sorry, but I can post to you, I'm in Wodonga VIC.  Cheers Peter

Hi all,

I have a HK steel rim that may be useful to someone for a 14 inch wheel conversion or need to make up a spare.  It has had some flaking rust issues but I have given it a good wire brush and painted it, the tyre joint reckons it's still solid enough but would recommend running a tube (it's highly recommended anyway they say in older rims like this one).  Postage is possible, as for price $15 + postage will get it.  I have a pic available too if you want to have a look.  Phone 0418451665 or reply here

Cheers

Peter

Interested in the radio, I'll send you a pm.

Cheers

Peter

This is now sold, thanks Allan!!

Hi all,

I have an engine stand that was used by Repco to mount reconditioned grey motors on in the workshop prior to shipping them out.  It would be a very handy item if you want to free up your engine stand but don't want to sit the engine on its sump.  It bolts to the two front engine mount holes and to the lower gearbox mounts on the back.  Can supply a pic if interested, just pm me or call 0418451665.  I'll need to weigh it, but if under 20kg I can post it, or freighting is fine too.  Pickup is welcome too if you're near Albury/Wodonga.  As for price happy to listen to an offer.

Regards

Peter

Still cleaning out the shed, I have a crankshaft, conrods/pistons, flywheel, thermotat housing, timing cover and backing plate, water pump (good for parts only), fuel pump (EK and later type) and a dent free sump left .

Happy to listen to offers and all of these items can be posted.  Located in Wodonga VIC and pickup is welcomed too if you're local.

Cheers

Peter

ok, that makes sense, thanks.

Peter

That was me who listed (and have relisted) that engine, thanks for the tips, I was 99% sure it was something like an industrial engine, but I was also advised through another forum that it may be a NASCO replacement block also.  It has never been grey, the paint is originally green. 

Anyway thanks again!

Peter

Yes they made column shift T400, I had a 308 T400 HZ Premier wagon with a factory bench seat and column shift, was a good combo actually!!

Cheers

Peter

Said he still raced the FC, must have been sitting there a while given the amount of crap that is lying in front of it now!!  ::)

No basis to this whatsoever, but IMHO I would hazard a guess to say the EJ as before this they had 'Station Sedan' badgework, from the EJ on they didn't.

Regards

Peter

How cool, the forum has a US correspondent!!

Cheers  ;D

Peter