Messages

Thanks Chuck & Fast_Eddie,
Will chase the cord up. :)
Thankyou Again,
Spider

Thankyou everyone for your help,
    Ken what do you mean by locating tags?, are these put into the rubber for the moulds to sit into. As i thought you just put the moulds into the rubber and they stayed in there on there own accord. Sorry for the questions but haven't done these before.
Regards Spider

Thanks Sarge,
              Your a champion.
Have sent you a private message
Cheers Spider

Hi To All,
             Just wondering what is the best cord  to run in the rubber, when fitting windscreens.
Cheers, Spider  

 ;D
      Bought the one of e-bay, it has already been setup for trimatic, so it should  be a hell of alot easier.
Cheers Spider

Cheers SRVLIVES,
                                  Your a champion, owe you a couple of beers. ;D
Cheers Spider

Thankyou to everyone for your help,
I think i wil go the EJ/Eh column auto just got to get one now. ::)
Cheers, Spider

Thanks everyone for your advice,
 Ken i had a look at the uni-joint for the rack and pinion and it has a short rod with 2 unijoints that has a round hole either end. One slides onto the rack & pinion itself and obviously the other for the steering column with holes either side, as if to run a bolt thru it to secure it. Would this be a lh lx type setup?
Regards Spider

I know its not a fe/fc, But am doing up a EH ute, Hr frontend, front mounted rack and pinion, suit small block chev, and wondering which is the best column to suit, the rack and pinion. And is there anyone in queensland that do these conversions :
Cheers Spider

hi To all, And hope you had a great xmas,
Wondering if anyone can tell me which column shift auto will fit a fe with a trimatic. The wife wants a column auto with the dial on the column, ::) I was told that ek column will fit, but just wondering if there is any others, as ek columns seems to be rare.
thankyou, Spider

Thanks  Sarge,
                         Very much appreciated. :)

Hi to all,
                   Still chasing the stainless trim for the front windscreen. And also i am after a ek auto steering column, as i want to adapt it to a trimatic, or does anyone know if there is another column auto that i can use. Thankyou and hope everyone has a MERRY XMAS.
Regards, Spider

Hi All,
        Wondering if anyone out there has a set of front windscreen stainless trim. After a set that has no dings in them.
 Please leave a message here or you can e-mail me at spider65@optusnet.com.au
Cheers, Spider :)

I say forget the supercharger, and just stick with the chev. I am dropping a chev into my eh ute thats got 400 plus horsepower. if the steering and brake system is set up properly there is know reason why it  wont be okay. As for legal problems in every state, i dont know about the other states, but dropping a chev into early holdens is easier now in queensland, So long as i am running a full chassis, discs all round, that is really it.
Dropping chevs into old holdens, have them so they are safe to drive, Nothing wrong with that, I would buy a commodore if i wanted something that handles nice and goes well, but wouldnt stand out like a small block chev in a old holden. New motors are nice, but i like to be able to lift the bonnet  look at my motor and be able to work on it. Not scrath my head and rely on computers to run the motor.
But Ol School and Rat Rods, cant beat it. JUST A OLD REV HEAD AT HEART
Cheers Spider :)

UTE HAS SOLD :)

Just had a go cant get past 10.134 >:(

Hi to all,  I am chasing a good set of chrome headlight rims, that have no pitting and in good condition with nice chrome work. Please e-mail me at spider65@optusnet.com.au , or leave a message here, UPDATE i am also chasing the trims that go across the top of the doors, on the outside for a FE
cheers spider:)

Hey A-C,
Could you e-mail me some photos to
spider65@optusnet.com.au
cheers mate, spider

Howdy everyone,
Been a while since i have been on the forum, so happy new year to everyone.
I am chasing foor door trim's for my fe special.
In good to perfect condition so they just have to be re-upholstered, and no cracks or broken pieces on the board.
I know im asking a bit much but you never know unless you ask.
Or if anyone knows another way of doing these door panels.
Am willing to pay good money for the right trims.
Cheers everyone, Spider
P.S. Also looking for a hr front-end in the brisbane area, if anyone has one for sale.
It is to go into a fj ute. Maybe Willing to buy from nsw, vic.

Hi to all,
                I am chasing a heap of glove box lid's, to airbrush and pinstripe. If anyone has a spare one or two or whatever, and interested in selling them, please let me know here or e-mail me at
spider65@optusnet.com.au

Cheer's Spider 8)