Re-activating my FE after it has been "Idle" for 8 years and (surprise) the front brakes were siezed ...
Managed to back off the brake shoes and get the drum off one side but the near side will not budge ...
Tried backing off the brake cylinder but the adjusting cover of the wheel cylinder is siezed on both ends ...
One can of WD40 and two weeks later it won't budge ...got to it with a big hammer but no good ... got a BIGGER hammer but no good ... got a F#### big hammer but still jammed ...
Short of attacking it with an angle grinder , has anyone got any ideas ??
Will removing the bolt from the brake anchor help ?
If I have to resort to more violence (ie , the angle grinder) , has anyone got a set of drums for sale ???
Regards , Dave .
what about bolting an old rim on, then welding a long bar/tube to it and trying to crack it that way :-\
If time is not important, a good extended soak with neat Molasses will kill the rust. May take a few days of application (because soaking in a Molasses bath is not possible).
Can only really think of getting a puller onto it and try yanking it off that way but you might have to sacrifise the bearing dust cover in the centre to do so. :-\
Im guessing you have already tried sitting the car on the ground with its own weight on the wheels and rocking it back and forth?
this seems to free up stuck drums when the handbrake has been left on and car not driven over a long period.
Cheers
Ed
OXY OR BLOW TORCH,JUST SLOWLY MOVE IT AROUND THE RIM OF THE DRUM,GIVE IT FEW HITS WITH YOUR BIG MFKN HAMMER & SHE SHOULD FALL OFF. ;D
Thanks guys ... will let you know how I go ... keep the ideas coming though ...cheers , Dave .
thanks for the -1... outa here
Sorry Ed ..didn't realise I did it !!! ...so now I know what that function is !!! Thanks for all the tips ...gunna try them all ... Dave .
Hi David,
I will have a full set of FE-FC front & rear drums and matched shoes (used but in good condition) for sale at my swap meet stall at the VIC FE-FC Holden auction on Sat 27th August along with a full set of re-co'd wheel cylinders (honed & new cups).
For details of the Auction refer here: http://fefcholden.org.au/forum/index.php/topic,19685.0.html (http://fefcholden.org.au/forum/index.php/topic,19685.0.html). Suggest you be early ;)
Regards,
Trevor_B
IT"S OFF !! ...and no damage ! .. thanks to all ...Pics tomorrow ...used a $15.95 gear puller and it worked perfectly ... makes up for all the times that a so-called simple jobs "stuff up" ... now all I need is two new Wheel cylinders !!!
"now all I need is two new Wheel cylinders !!!"
You could have a brake service place repair your old cylinders or have them re sleeved with stainless steel. Probably cheaper than new cylinders
Keith
Thanks Keith ... I see Rares want $92.50 each for them ! ... I'll check the local places unless anyone can recommend somewhere I can send them ... Cheers , Dave .
How bad are they press the cylinders out and get some new cups give them a hone if they arent scored off you go...
David,
You could try Nepean Spares, St Marys NSW, ask for Geoff, they will have them.
Cheers
John
The pics ...
The $15.95 gear/hub puller ...
(http://i1211.photobucket.com/albums/cc439/DavidLakin/IphoneAugust2011042.jpg)
Turned out to be perfect for the job ...
Puller jaws fit perfectly into the first groove of the finned drum ...
http://i1211.photobucket.com/albums/cc439/DavidLakin/IphoneAugust2011037.jpg
Sorry ... ???
(http://i1211.photobucket.com/albums/cc439/DavidLakin/IphoneAugust2011037.jpg)
Dozen or so cranks with the rachet ...and she's off !!!
(http://[img]http://i1211.photobucket.com/albums/cc439/DavidLakin/IphoneAugust2011038.jpg)[/img]
GRRRRR !!
(http://i1211.photobucket.com/albums/cc439/DavidLakin/IphoneAugust2011038.jpg)
And cthe cause of the problem ...
What do you think gentlemen ??? replace the whole thing ????
(http://i1211.photobucket.com/albums/cc439/DavidLakin/IphoneAugust2011040.jpg)
Take them to a head place or someone with a bead blaster do the whole lot re paint and clean it all up re hone and re build the cylinders you dont get quality like them 50 year old part.
Looks like it came off easier after you took the wheel nuts off.... :P ...hehehe...I bought brand new wheel cylinders for mine a few months ago and they cost me $66 each from my local brake guy here in SA.Not Stainless but for that price,who cares?....
Lol ... Well spotted ...only left them on til it started to move ! For that price did u just get the cylinders or cups and all ? ... Cheers Dave .
Hi David,
Great pictures so far. A question for you on where your $15.95 Gear/ hub puller came from ?
It looks to be a very handy tool for the toolbox and at a reasonable price too.
Keep up the good work (go the mighty FE)
Cheers Stewy 8)
Hi Stewie . Got mine from Not Just Tools in Wauchope ... Should be able to pick one up at most tool shops but the 6 inch jaws are perfect for the drums . Let me know if you want one . Cheers Dave .
Quote from: David Lakin on August 16, 2011, 01:05:06 PM
Sorry Ed ..didn't realise I did it !!! ...so now I know what that function is !!! Thanks for all the tips ...gunna try them all ... Dave .
all good, I jumped the gun a bit too.
Sweet ...I fixed it up though ... Dave
PM sent