Show Posts
|
Pages: 1 [2] 3 4 ... 7
|
24
|
General / General Board / Re: CD players
|
on: July 08, 2005, 01:26:04 AM
|
for those considering mounting in the glove box, 19mm timber fits into the gove box lower support like a glove and you just need a screw to hold it in place as security. from there just make up a mounting platform for the radio.
If you are going to mount behind the speaker grill, if you hindge at the bottom ensure you have a strong clasp so it doesn't keep falling open as you drive along. I have been tring to find some small gas struts that you can use for holding the grill open (or shut I spose if you do hindge from the bottom) but no luck as yet.
As a rule, I direct wire the power from the battery via a dash board switch. I find that way I can turn it off easily when needed (ie hear sirens, phone rings etc) and you just wait until the next set of lights if you cannot reach the unit to change CD's or stations.
|
|
|
28
|
Technical Board / Modification Help / Re: 186--FC--HR CHASSIS
|
on: June 03, 2005, 08:10:49 AM
|
Torque That was a wooden spoon and porriage bowl (three on tree) hr gear box. (I believe as not my car in pic) You do not need to mod the hump to stick one of those in (I believe). The aussie four speed is a total different matter. See Alex's post on his mods when he slipped a aussie four into Rock'n'Roll http://www.fefcholden.org.au/cgi-bin/yabb/YaBB.cgi?board=hotup;action=display;num=1022339013The bracket is based of the standard FC one. I think that one in the pic was a CRS made backet. Mine was made by some butcher who cut some bits out of an FC one and I added some steel when I got it for strength. Have yet to get around to making a proper one. Will wait to cross that bridge when I drop my aussie 4 in. cheers Al Flamed FE
|
|
|
29
|
General / General Board / Re: O/T Barris Movie and TV car auction.
|
on: June 03, 2005, 01:55:48 AM
|
Went to the Barris site IHADAV8 posted and bought a couple of his books for myself for upcoming birthday & father’s day. They arrived yesterday and managed a quick peek at the flamed book before they were confiscated until I was "officially" given them.
Let me just say WOW. some of the kustomizing in there was fantastic. If you like wild then get yourself a copy of these to read.
Cheers Al
|
|
|
33
|
Technical Board / Modification Help / Re: Aussie 4spd shifter conversion for bench seat.
|
on: May 26, 2005, 08:22:10 AM
|
Sarge
If you are talking the CAD stuff. It was based of my drawings based off alex's post. I always planned to draw up the rods needed, but I then my wife started to swell and along came my little boy (child number two). I've had a shell and half finished aussie 4 speed adapter sitting on my garage floor for over two years now. 50th Ann nationals will hopefully make me pull the finger out and finish it all off. (provide the friartucking boss doesn't send me to India too many times between now and then!!)
Cheers Alan
|
|
|
37
|
General / FE-FC Holden Nationals / Happy Nationals
|
on: March 23, 2005, 03:06:05 AM
|
Well I'm back in Australia long enough for a quick holiday with the family and sort out the ten ton of paper work on my desk before heading back to the land of curries for another month or so.
Just a quick note to wish everyone a Happy Nationals and a safe trip to and home again
and that I'm jealous of you all!!
Have a great time and enjoy the beer and sights.
Al Flamed FE
|
|
|
|