camxsmith
|
![](http://forum.fefcholden.club/Themes/default/images/post/xx.gif) |
« Reply #360 on: August 23, 2021, 02:19:11 PM » |
0
|
Repaired a couple of spots over the weekend. Both near the drivers side A Pillar. (sorry light was not good) ![](https://i.imgur.com/6zjcsXfm.jpg) Cut the rust out and put on some rust convert ![](https://i.imgur.com/6e1yTN3m.jpg) Weld thru primer under new piece test fitting ![](https://i.imgur.com/VDEzm6Lm.jpg) ![](https://i.imgur.com/M4na0oAm.jpg) Weld it in coat with primer ![](https://i.imgur.com/bBaiF0Am.jpg) Another bad spot under the front guard ![](https://i.imgur.com/MRiJzWZm.jpg) Cut out ![](https://i.imgur.com/hhX48mCm.jpg) Make a new piece ![](https://i.imgur.com/uJNtIFhm.jpg) Weld it in and coat with some primer ![](https://i.imgur.com/N1tv8Uim.jpg)
|
|
|
Logged
|
|
|
|
camxsmith
|
![](http://forum.fefcholden.club/Themes/default/images/post/xx.gif) |
« Reply #361 on: August 28, 2021, 08:28:58 PM » |
0
|
|
|
|
Logged
|
|
|
|
mcl1959
|
![](http://forum.fefcholden.club/Themes/default/images/post/xx.gif) |
« Reply #362 on: August 28, 2021, 08:30:17 PM » |
0
|
That is super neat Cam. Well done as usual
|
|
|
Logged
|
|
|
|
camxsmith
|
![](http://forum.fefcholden.club/Themes/default/images/post/xx.gif) |
« Reply #363 on: October 01, 2021, 10:52:43 AM » |
0
|
|
|
|
Logged
|
|
|
|
camxsmith
|
![](http://forum.fefcholden.club/Themes/default/images/post/xx.gif) |
« Reply #364 on: October 28, 2022, 07:59:17 PM » |
0
|
Hi All, its been a long time .. Hope all are doing well. I'm still on the forum, and still love the posts. Caught up with Brett_f today grabbed some gems.. Front spears and tail light surrounds.. Has got my FC blood flowing again, and wanting to do more on the car again. So I have some pics and posts to come soon.
|
|
|
Logged
|
|
|
|
camxsmith
|
![](http://forum.fefcholden.club/Themes/default/images/post/xx.gif) |
« Reply #365 on: October 31, 2022, 09:12:06 AM » |
+1
|
Some Pics of the floor coated in the kbs products ![](https://i.imgur.com/Tu6VfI9m.jpg) Added a plate in the roof for the sun visor. Formed a plate to match the roof line Used a self tapper to hold it in place ![](https://i.imgur.com/zlmKV4zm.jpg) Spot welded it in place ![](https://i.imgur.com/VeOct00m.jpg) Used some sealer and rivet nuts to hold the center bar in place ![](https://i.imgur.com/ISwXXfKm.jpg)
|
|
|
Logged
|
|
|
|
Mal W
|
![](http://forum.fefcholden.club/Themes/default/images/post/xx.gif) |
« Reply #366 on: October 31, 2022, 10:14:48 AM » |
0
|
Looking great Cam. Good idea with the sun visor bracket strengthening. Think I may also do that with mine while its in bits.
Mal
|
|
|
Logged
|
Malcolm WHITTAKER
|
|
|
camxsmith
|
![](http://forum.fefcholden.club/Themes/default/images/post/xx.gif) |
« Reply #367 on: November 11, 2022, 10:36:55 AM » |
0
|
|
|
|
Logged
|
|
|
|
camxsmith
|
![](http://forum.fefcholden.club/Themes/default/images/post/xx.gif) |
« Reply #368 on: November 11, 2022, 10:43:14 AM » |
0
|
Weber 34 adm accelerator mount bracket. Started with a lot of lines and measurements, making sure cable will not hit the air cleaner and come over rocker cover ![Huh](http://fefcholden.org.au/forum/Smileys/default/huh.gif) ![](https://i.imgur.com/igxefdwm.jpg) Drilled holes, folded on the lines and added some weld for extra strength ![](https://i.imgur.com/g9817rgm.jpg) Final test run ![](https://i.imgur.com/3n5I1bmm.jpg) Lick of paint and happy with its look and how it works
|
|
|
Logged
|
|
|
|
camxsmith
|
![](http://forum.fefcholden.club/Themes/default/images/post/xx.gif) |
« Reply #369 on: November 11, 2022, 10:48:07 AM » |
0
|
Finishing off the dash for the altered gauge panel. Cuts made ![](https://i.imgur.com/NnVXHUmm.jpg) Replacement lip hammed out ![](https://i.imgur.com/fAIdzlXm.jpg) Welded in and cleaned up, happy with the result ![](https://i.imgur.com/HIfVUUCm.jpg)
|
|
|
Logged
|
|
|
|
Errol62
|
![](http://forum.fefcholden.club/Themes/default/images/post/xx.gif) |
« Reply #370 on: November 11, 2022, 10:57:48 PM » |
0
|
I just did a cable setup on the 179 X2 in my FB ute. The jugs bolt straight on the manifold which makes for very little clearence to the manifold. Also I'm running a tall tappet cover for roller rockers clearence, exacerbating the issue.I ended up setting it up to pull down on the manifold side. Using a hx v8 cable. I use the original pedal, extending to a 60mm radius, with outer bracket sandwiched between brake union and subframe leg. ![](https://uploads.tapatalk-cdn.com/20221111/4c62bff47ee74b70f0851b2c6691d02d.jpg) ![](https://uploads.tapatalk-cdn.com/20221111/3a1fc1b1f4f00fb1aab346d5419322a2.jpg) Sent from my SM-G781B using Tapatalk
|
|
« Last Edit: January 06, 2024, 03:48:37 PM by RET »
|
Logged
|
|
|
|
camxsmith
|
![](http://forum.fefcholden.club/Themes/default/images/post/xx.gif) |
« Reply #371 on: March 17, 2023, 03:35:42 PM » |
0
|
|
|
|
Logged
|
|
|
|
camxsmith
|
![](http://forum.fefcholden.club/Themes/default/images/post/xx.gif) |
« Reply #372 on: January 06, 2024, 10:00:13 AM » |
+1
|
|
|
|
Logged
|
|
|
|
ardiesse
|
![](http://forum.fefcholden.club/Themes/default/images/post/xx.gif) |
« Reply #373 on: January 06, 2024, 12:46:27 PM » |
0
|
Well done!
Rob
|
|
|
Logged
|
Remember: if your Holden's not leaking oil, it doesn't have any.
|
|
|
Jolls
nsw-club
Full Member
![*](http://forum.fefcholden.club/Themes/default/images/star.gif) ![*](http://forum.fefcholden.club/Themes/default/images/star.gif)
Offline
Model: FC
Posts: 199
|
![](http://forum.fefcholden.club/Themes/default/images/post/xx.gif) |
« Reply #374 on: January 07, 2024, 03:28:53 PM » |
0
|
Thanks, that is such a neat solution to the problem. I will add that to my list of jobs to do.
Cheers
Jolls
|
|
|
Logged
|
Cheers n Beers
Jolls
|
|
|
FireKraka
|
![](http://forum.fefcholden.club/Themes/default/images/post/xx.gif) |
« Reply #375 on: January 08, 2024, 01:23:08 PM » |
0
|
Nice work on the wiper arms Cam
|
|
|
Logged
|
|
|
|
|