FE-FC Holden Discussion Forum
May 02, 2024, 03:14:45 PM
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
News
: The FE-FC Holden Car Club of NSW are proud to host the
19th FE-FC Holden Nationals
. Check out the
announcement video
for more.
Home
Help
Search
Calendar
Login
Register
FE-FC Holden Discussion Forum
>
Technical Board
>
Restoration Help
(Moderators:
RET
,
Glenn 'Stinky' Stankevicius
,
gp
) >
Indicator switch assembly
Pages: [
1
]
Go Down
« previous
next »
Add bookmark
|
Print
Author
Topic: Indicator switch assembly (Read 3660 times)
abletec
Newbie
Offline
Posts: 8
Indicator switch assembly
«
on:
May 22, 2020, 09:43:18 PM »
0
I've a question for somone that has taken apart and reassembled a 6 wire indicator switch on an FC. I have 3 small ball bearings but cannot find where they go. I have the switch cleaned and back together without the balls and it seems to function mechanically though not tested electrically. Nine springs fitted. Do the balls go on the centre spring under each brass contact block? Should there be more than 3 balls? Thanks for any assistance.
Logged
abletec
Newbie
Offline
Posts: 8
Re: Indicator switch assembly
«
Reply #1 on:
May 24, 2020, 11:26:06 AM »
0
I can't believe that no one has ventured to cleaning and rebuilding an indicator switch! Very simple, just need to know where the balls fit in. Can find nothing on line for Holden or any other make for that matter. Unfortunately mine sprang apart before I could see the correct positions. Probably need to find another one somewhere. I might need to do a video when I can get it together..
Logged
mcl1959
vic-club
Guru
Offline
Posts: 6155
FE's rule
Re: Indicator switch assembly
«
Reply #2 on:
May 24, 2020, 04:28:28 PM »
0
Ok, so I was tempted to reply to your post When I saw it because I think the balls go in the bottom of the brass cups so that the springs sit on them. But I’m not 100% sure
30 years ago I pulled one apart and springs and balls went everywhere. I said at the time I’m never doing that again.
So far I haven’t
I’ve been lucky enough over the years to find quite a lot of NOS ones of these so I’ve never had to worry about cleaning/restoring them.
Doesn’t help much I guess.
Ken
Logged
Errol62
Guru
Offline
Posts: 1149
Re: Indicator switch assembly
«
Reply #3 on:
May 24, 2020, 10:58:44 PM »
0
What Ken said pretty much exactly my experience. No need to dick with it so don’t. A lesson I learned early in my early holden fiddling career. I’ve pulled apart seat runners, steering boxes, speedos, regulators, carbies, diffs and quarter vents. But them pesky indicator switches have got me beat.
Sent from my iPad using Tapatalk
Logged
abletec
Newbie
Offline
Posts: 8
Re: Indicator switch assembly
«
Reply #4 on:
May 27, 2020, 07:28:11 PM »
0
Thanks for your responses. The switch seems to be in good condition just in many pieces. I will try to put it back together. A job where you need 3 hands.
Logged
59wagon
Full Member
Offline
Model: FC
Posts: 150
Re: Indicator switch assembly
«
Reply #5 on:
June 06, 2020, 08:34:36 AM »
0
Hi mate, I can’t remember what my FC switch looked like but I pulled the FB one apart a while ago. It may be different but you might get an idea of how it goes together from the pictures. There were 4 ball bearings that sat in grooves on the metal casting, then the plastic/Bakelite part goes on top, matching the grooves (arrowed in the photo). The bearings allow the switch to slide smoothly from side to side. Six springs then covered by the brass L-shaped bits, followed by the cover with the wires attached. Yes, you need to be an octopus to put it together.
Cheers, John
Sent from my iPhone using Tapatalk
Logged
FireKraka
Senior Member
Offline
Model: FC
Posts: 646
Re: Indicator switch assembly
«
Reply #6 on:
June 06, 2020, 10:37:26 AM »
0
Always love your posts Bones very informative and detailed.
Neil
Logged
Errol62
Guru
Offline
Posts: 1149
Re: Indicator switch assembly
«
Reply #7 on:
June 06, 2020, 12:32:52 PM »
0
Ditto John and Neil. Was wondering if you’d pipe up on this after your confessions on the finny site. If anyone has the patience to get all those tiny wee bits back together it’s you mate.
Sent from my iPad using Tapatalk
Logged
abletec
Newbie
Offline
Posts: 8
Re: Indicator switch assembly
«
Reply #8 on:
June 18, 2020, 03:01:39 PM »
0
Hi John and others for your contributions. John your photos and description are very clear and make a lot of sense. I had managed to assemble the switch but don't think that I have got the 3 balls in the correct place after seeing your photos. Also the switch doesn't slid smoothly so I needed to back the screws off a bit. I have the 3 balls on top of the 3 centre springs (9 springs in all). Time to remove again and place the balls as per the photo.
Putting the switch back together is do-able but extra hands would have made it easier. I removed the switch entirely and assembled it while holding it like a sandwich. Then I wrapped insulation around both ends before screwing it in. I used solvent on the insulation tape while pulling it put while the screws were not fully in. We will need to learn these restoration tips when all new spare parts stock runs out.
Logged
Pages: [
1
]
Go Up
Add bookmark
|
Print
« previous
next »
Share this topic...
In a forum (BBCode)
[url=http://forum.fefcholden.club/index.php?topic=27806.0]Indicator switch assembly[/url]
In a site/blog (HTML)
Indicator switch assembly
Jump to:
Please select a destination:
-----------------------------
General
-----------------------------
=> General Board
=> FE-FC Holden Nationals
===> 2020 - Wangaratta - 18th FE-FC Holden Nationals
===> 2012 - Perth - 14th FE-FC Nationals
=> Events, Shows etc
-----------------------------
Technical Board
-----------------------------
=> Restoration Help
=> Modification Help
=> General Technical
-----------------------------
Galleries
-----------------------------
=> Members' FEs and FCs
===> Members' Other Vehicles
=> Project Cars - FEs and FCs Under Construction
===> Members' Other Vehicles Under Construction
=> Members' Completed FE-FC Projects
===> Completed Projects - Other Vehicles
=> Unreal Cars - Members' Artwork
=> Little Cars - Members' Model FEs and FCs
=> Original Advertisements, Brochures
=> Other Images
-----------------------------
For Sale and Wanted
-----------------------------
=> Cars For Sale
=> Cars Wanted
=> Parts For Sale
=> Reproduction Parts
=> Parts Wanted
=> Other Stuff For Sale
=> Other Stuff Wanted
=> Auction and Trade Links
Loading...