News:

Are you a member of one of the FE-FC Holden Car Clubs of Australia ? If you are, get access to the Club-Member-only area of this discussion board. Send an IM to the board admin, including your real name and club to get access.

Main Menu

Seat surround handle

Started by NES304, May 14, 2009, 04:44:21 PM

Previous topic - Next topic

NES304

Any one know how to remove this so I can fit my new seat surrounds?
Cheers



Ed

There should be a grub screw holding it on.
in the shed

FX1975

There is a grub screw holding it on from underneath

                               

oldgmh

there is a small screw with an allan key head located underneath the handle.   :o :o

TTV6FC

Underneath the handle,there should be a small grub screw with an Allen key head holding it onto the shaft....What the hell,everone else has had a go...  ??? ;D
Run your fingers over my Holden and I'll run my Holden over your fingers!!!!

FC427

OK  ;D ;D There is a small allen head grub screw located under the seat adjustment knob just undo this and it should come of .......FC427.....Bah Bah
As I lay rubber down the street I pray for traction I can keep, but if I spin and begin to slide please dear god protect my ride

Damo58

 ;D ;D iam not sure but i think there is a small grub screw with an allen key head on it  ;D ;D
Iam good just ask me :)

NES304

So I'm guessing its some kind of alen key grub screw?????

Pissin myself laughing.....



customFC

Get a big claw hammer and lever it off.
.
.
.
.
.
.
.
Before you put it back on, you will have to turn it over and loosen the small grub screw.

Regards
Alex

Ed

in the shed

EffCee

If all else fails you could get the oxy out, heat it till it glows bright red, this will allow the know to expand enough to release from the seat lever, (will more than likely set fire to the seat) Better to remove the seat as you don't want your car to catch fire.

Once off, cool, then loosen grub screw for reinstallation.

(May as well get it rechromed too as there won't be any chrome left on it)

;D ;D
Canberra, ACT

F4+ ;)

ridgey_didge

I've always done it this way -
1.  Hold the allen key in a vice attached to work bench. 
2.  Place the grub screw in the seat handle on allen key* and turn as far as possible.
3.  Lift screw off allen key, rotate the job and repeat step 2.
4.  Keep repeating step 3 as many times as necessary.

To reinstall do these steps in reverse.

*  Removal of the seat from the car first is entirely optional. ;)

Cheers
David

Johns

That's all Ok, but how do you get the one on the passengers side off ???
Now that I've got the beige with the grey, I'm looking for the cream, the bone, the ivory and the off white

Paul In Ireland

Well, first of all get an allen key.....  ;D
The International FE FC Fleet of Ireland
Education is where you read the fine print. Experience is what you get when you don't.

ridgey_didge

Quotehow do you get the one on the passengers side off

You need an allen key that turns in the other direction for that side.

EffCee

Canberra, ACT

F4+ ;)

oldgmh

Come on guys - stop taking the piss out of the bloke - all he wants to do is remove his knob.   ::) ::)

The correct way to do it is :

pull it very hard ( maybe a couple of pulls ) and you should feel it when it happen and releases..... so keep pulling until it happens ... :o :o


colt

Don't forget to cough as you pull on your little Allen Key. It'll come easier.
colt

NES304

Do I dare ask for the placement of the little black foam pieces that comes with the kit?



oldgmh